Inactive

This notice is for Solicitation Number 36C24220R0029 - Install new floors in the Pharmacy IV Room 1B at James J. Peters VA Medical Center, 130 West Kingsbridge Rd. Bronx, New York, 10468. This shall b... This notice is for Solicitation Number 36C24220R0029 - Install new floors in the Pharmacy IV Room 1B at James J. Peters VA Medical Center, 130 West Kingsbridge Rd. Bronx, New York, 10468. This shall be a Service-Disabled Veteran Owned Small Business Set-Aside (SDVOSB). As a result, all SDVOSB's may submit an offer, which will be considered by the agency. This project is classified under NAICS Code 238330 and has a size standard of $16.5 Million. The cost estimate range for this project is $25,000.00 to $100,000.00. SCOPE OF WORK: Install new floors in the Pharmacy IV Room 1B. This work is to be done using the product described below or an approved equivalent. See PRODUCT DESCRIPTION AND PHYSICAL CHATACTERISTICS below. This is to prepare and coat the floors in the Pharmacy IV Room in 1B of approx. 633 square feet Scope of Work (I.V. Room). The contractor shall remove the existing old floor (sheet viny). There is no asbestos under current floor as it was removed during the last renovation eight (8) years ago. This room is currently empty and does not require removal of any plumbing, partitions, insulations, barriers, etc. Mechanically prepare all accessible areas with the use of a Blastrac machine. This procedure removes: All surface laitance, oil, grease and dirt from the substrate and provides a mechanical profile to enhance bonding. Stonblend GSI - A three-component, troweled, 3/16" mortar consisting of epoxy resin, curing agent. Colored quartz silica aggregate, a two-component, clear UV resistant epoxy grout coat sealer and a two component, Water based, non-reflective aliphatic polyurethane coating. New flooring does not require bracing. New flooring does not require stripping and waxing after installation. Contractor shall be responsible for removing all debris. New flooring requires at least 1-year warranty from acceptance date. PRODUCT DESCRIPTION AND PHYSICAL CHARACTERISTICS Stonblend GSI-G is a nominal 3/16 in./5 mm flooring system that offers a cost-effective alternative to terrazzo and incorporates recycled glass in the surface of the floor. It combines striking, decorative looks, excellent chemical and wear resistance, cleanibility and UV resistance with an easy to maintain surface. All standard colors contain 10% recycled glass chips per unit. PHYSICAL CHARACTERISTICS Compressive Strength . . . . . . . . . . . ................ 6,000 psi (ASTM C579) ........................................ after 7 days Tensile Strength . . . . . . . . . . . . . . . . . . . . . . .... 1,500 psi (ASTM C-307) Flexural Strength . . . . . . . . . . . . . . . . . . . . . . .... 2,200 psi (ASTM C-580) Flexural Modulus of Elasticity. . . . . . . . . . . .... 5.0 x 105psi (ASTM C-580) Hardness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... 85 to 90 (ASTM D-2240, Shore D) Impact Resistance. . . . . . . . . . . . . . . . . . . . ... >160 in./lbs (ASTM D-2794) Abrasion Resistance . . . . . . ... .0.06 gm max. weight loss (ASTM D-4060, CS-17) Flammability (ASTM E-648, E-662). . . . . . . . . . . . . . . . . . . . ... Class 1 Thermal Coefficient of Linear Expansion . . . . . . . . . . . . . . .... .1.3 x 10-5 in./in.°F (ASTM C-531) VOC Content . . . . . . . . . . . . . ... Stonblend Primer - 75 g/l (ASTM D-2369, Method E) Stonblend GSI-G Base -17 g/l ............................................ Stonblend Grout Coat - 52 g/l ......................................................... Stonkote CE4 - 34 g/l ...................................... Stonseal CF7 - 47 g/l (Method C) Cure Rate . . . . . . . . . . . . . . . . . . . 12 hours for foot traffic (@ 77°F/25°C) 24 hours for normal operations Note: The above physical properties were measured in accordance with the referenced standards. Samples of the actual floor system, including binder and filler, were used as test specimens. All sample preparation and testing is conducted in a laboratory environment, values obtained on field applied materials may vary and certain test methods can only be conducted on lab made test coupons. PROJECT COMPLETION: 28 Calendar Days All other details and information shall be contained in the solicitation which shall be posted on www.fbo.gov. The solicitation will be released on or about 12/20/2019. The response submittal address, date and time will be included in the solicitation. This project requires bonding. All prospective bidders must be currently registered in www.sam.gov and be registered and verified as a SDVOSB in www.vip.vetbiz.gov at the time of offer submission and before award of this procurement. End of Description.

Inactive Service-Disabled Veteran-Owned Small Business (SDVOSB) Set-Aside (FAR 19.14)

This notice is for Solicitation Number 36C24220R0029 - Install new floors in the Pharmacy IV Room 1B at James J. Peters VA Medical Center, 130 West Kingsbridge Rd. Bronx, New York, 10468. This shall b... This notice is for Solicitation Number 36C24220R0029 - Install new floors in the Pharmacy IV Room 1B at James J. Peters VA Medical Center, 130 West Kingsbridge Rd. Bronx, New York, 10468. This shall be a Service-Disabled Veteran Owned Small Business Set-Aside (SDVOSB). As a result, all SDVOSB's may submit an offer, which will be considered by the agency. This project is classified under NAICS Code 238330 and has a size standard of $16.5 Million. The cost estimate range for this project is $25,000.00 to $100,000.00. SCOPE OF WORK: Install new floors in the Pharmacy IV Room 1B. This work is to be done using the product described below or an approved equivalent. See PRODUCT DESCRIPTION AND PHYSICAL CHATACTERISTICS below. This is to prepare and coat the floors in the Pharmacy IV Room in 1B of approx. 633 square feet Scope of Work (I.V. Room). The contractor shall remove the existing old floor (sheet viny). There is no asbestos under current floor as it was removed during the last renovation eight (8) years ago. This room is currently empty and does not require removal of any plumbing, partitions, insulations, barriers, etc. Mechanically prepare all accessible areas with the use of a Blastrac machine. This procedure removes: All surface laitance, oil, grease and dirt from the substrate and provides a mechanical profile to enhance bonding. Stonblend GSI - A three-component, troweled, 3/16" mortar consisting of epoxy resin, curing agent. Colored quartz silica aggregate, a two-component, clear UV resistant epoxy grout coat sealer and a two component, Water based, non-reflective aliphatic polyurethane coating. New flooring does not require bracing. New flooring does not require stripping and waxing after installation. Contractor shall be responsible for removing all debris. New flooring requires at least 1-year warranty from acceptance date. PRODUCT DESCRIPTION AND PHYSICAL CHARACTERISTICS Stonblend GSI-G is a nominal 3/16 in./5 mm flooring system that offers a cost-effective alternative to terrazzo and incorporates recycled glass in the surface of the floor. It combines striking, decorative looks, excellent chemical and wear resistance, cleanibility and UV resistance with an easy to maintain surface. All standard colors contain 10% recycled glass chips per unit. PHYSICAL CHARACTERISTICS Compressive Strength . . . . . . . . . . . ................ 6,000 psi (ASTM C579) ........................................ after 7 days Tensile Strength . . . . . . . . . . . . . . . . . . . . . . .... 1,500 psi (ASTM C-307) Flexural Strength . . . . . . . . . . . . . . . . . . . . . . .... 2,200 psi (ASTM C-580) Flexural Modulus of Elasticity. . . . . . . . . . . .... 5.0 x 105psi (ASTM C-580) Hardness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... 85 to 90 (ASTM D-2240, Shore D) Impact Resistance. . . . . . . . . . . . . . . . . . . . ... >160 in./lbs (ASTM D-2794) Abrasion Resistance . . . . . . ... .0.06 gm max. weight loss (ASTM D-4060, CS-17) Flammability (ASTM E-648, E-662). . . . . . . . . . . . . . . . . . . . ... Class 1 Thermal Coefficient of Linear Expansion . . . . . . . . . . . . . . .... .1.3 x 10-5 in./in.°F (ASTM C-531) VOC Content . . . . . . . . . . . . . ... Stonblend Primer - 75 g/l (ASTM D-2369, Method E) Stonblend GSI-G Base -17 g/l ............................................ Stonblend Grout Coat - 52 g/l ......................................................... Stonkote CE4 - 34 g/l ...................................... Stonseal CF7 - 47 g/l (Method C) Cure Rate . . . . . . . . . . . . . . . . . . . 12 hours for foot traffic (@ 77°F/25°C) 24 hours for normal operations Note: The above physical properties were measured in accordance with the referenced standards. Samples of the actual floor system, including binder and filler, were used as test specimens. All sample preparation and testing is conducted in a laboratory environment, values obtained on field applied materials may vary and certain test methods can only be conducted on lab made test coupons. PROJECT COMPLETION: 28 Calendar Days All other details and information shall be contained in the solicitation which shall be posted on www.fbo.gov. The solicitation will be released on or about 12/20/2019. The response submittal address, date and time will be included in the solicitation. This project requires bonding. All prospective bidders must be currently registered in www.sam.gov and be registered and verified as a SDVOSB in www.vip.vetbiz.gov at the time of offer submission and before award of this procurement. End of Description.