DY20 Dry-dock Repair to Coast Guard Cutter Cheyenne & Barge
The U.S. Coast Guard is looking for sources which would be interested in performing dry-dock repairs for Coast Guard Cutter CHEYENNE. The performance period of this upcoming dockside is 21 July – 16 S... The U.S. Coast Guard is looking for sources which would be interested in performing dry-dock repairs for Coast Guard Cutter CHEYENNE. The performance period of this upcoming dockside is 21 July – 16 September 2020. It is anticipated requests for quotes will be issued around 22 February 2020 and the contract would be awarded around 22 May 2020. Coast Guard Cutter CHEYENNE is a 75’ River Buoy Tender home ported in St. Louis, MO. There are approximately 62 work items in the requirement as noted below: WORK ITEM 1: Hull Plating (Side Scan), Ultrasonic Testing - Tender WORK ITEM 2: Hull Plating (U/W Body), Inspect - Tender WORK ITEM 3: U/W Body, Preserve (100%) - Tender WORK ITEM 4: Hull Plating Freeboard, Preserve “100%” - Tender WORK ITEM 5: Hull and Structural Plating -{Insert Plate Size (i.e. 1/2” or 5/16”, etc.) Steel Plate, Renew WORK ITEM 6: Appendages (U/W), Leak Test - Tender WORK ITEM 7: Appendages (U/W) - Internal, Preserve - Tender WORK ITEM 8: Voids (Non-Accessible), Leak Test - Tender WORK ITEM 9: Voids (Non-Accessible), Internal Surfaces, Preserve WORK ITEM 10: Tanks (MP Fuel Service), Clean and Inspect - Tender WORK ITEM 11: Tanks (Ballast), Clean and Inspect - Tender WORK ITEM 12: Voids (Accessible), Clean and Inspect WORK ITEM 13: Propulsion Shafting; Remove, Inspect, and Reinstall WORK ITEM 14: Propulsion Shaft Seals, Mechanical Clean and Inspect WORK ITEM 15: Propulsion Shaft Seals, Mechanical Overhaul and Inflatable Renew WORK ITEM 16: Propulsion Shafting, Straighten WORK ITEM 17: Propulsion Shafting; Remove, Inspect, and Reinstall WORK ITEM 18: Propulsion Shaft Bearings (External), Check Clearances WORK ITEM 19: Propulsion Shaft Bearings (External), Renew WORK ITEM 20: Stern Tube Interior Surfaces, Preserve 100% WORK ITEM 21: Propellers, Clean And Inspect WORK ITEM 22: Propeller, Perform Minor Repairs and Reconditioning WORK ITEM 23: Propellers, Remove, Inspect, and Reinstall WORK ITEM 24: Keel Coolers, Clean, Inspect and Hydro WORK ITEM 25: Fathometer Transducer, General Maintenance WORK ITEM 26: Sea Valves and Waster Pieces, Overhaul Or Renew WORK ITEM 27: Rudder Assembly; Remove, Inspect And Reinstall WORK ITEM 28: Rudder(s), Preserve (“100%”) WORK ITEM 29: Spuds, Overhaul - Tender WORK ITEM 30: Spud Wells, Preserve - Tender WORK ITEM 31: Spud Wells, Inspect - Tender WORK ITEM 32: Sewage Holding Tank(s), Clean and Inspect - Tender WORK ITEM 33: Decks - Exterior, Preserve (“Non-Skid Broadcast Grit” System) - Tender WORK ITEM 34: Cathodic Protection / Magnesium Anodes, Renew - Tender WORK ITEM 35: Drydock - Tender WORK ITEM 36: Temporary Services, Provide - Tender WORK ITEM 37: Sea Trial Performance, Support, Provide WORK ITEM 38: Hull Plating (Side Scan), Ultrasonic Testing - Barge WORK ITEM 39: Hull Plating (U/W Body), Inspect - Barge WORK ITEM 40: U/W Body, Preserve (100%) - Barge WORK ITEM 41: Hull Plating Freeboard, Preserve – Partial - Barge WORK ITEM 42: Appendages (U/W), Leak Test - Barge WORK ITEM 43: Appendages (U/W) - Internal, Preserve - Barge WORK ITEM 44: Voids (Non-Accessible), Leak Test - Barge WORK ITEM 45: Voids (Non-Accessible), Internal Surfaces, Preserve WORK ITEM 46: Tanks (MP Fuel Service), Clean and Inspect - Barge WORK ITEM 47: Tanks (Potable Water), Clean and Inspect - Barge WORK ITEM 48: Tanks (Ballast), Clean and Inspect - Barge WORK ITEM 49: Keel Coolers, Clean, Inspect and Hydro WORK ITEM 50: Fathometer Transducer, General Maintenance WORK ITEM 51: Sea Valves and Waster Pieces, Overhaul or Renew WORK ITEM 52: Hull Fittings (Weight Handling Rigging Hardware), Inspect and Test - Barge WORK ITEM 53: Spuds, Overhaul - Barge WORK ITEM 54: Spud Wells, Preserve - Barge WORK ITEM 55: Spud Wells, Inspect - Barge WORK ITEM 56: Tanks (Ballast), Preserve “Partial” WORK ITEM 57: Decks – Exterior (Buoy or Construction Deck), Preserve 100% WORK ITEM 58: Cathodic Protection / Magnesium Anodes, Renew - Barge WORK ITEM 59: Drydock - Barge WORK ITEM 60: Boat Davit Winch, Shrink Wrap WORK ITEM 61: Buoy and Cargo Handling Crane, Shrink Wrap WORK ITEM 62: Lead-Based Paint and Asbestos-Containing Material, Perform Spot Abatement All repairs will take place at the vendor’s facility. Companies which would be interested in submitting a proposal for this requirement should reply to this sources sought notice noting their business size status such as large business, small business, HUBZone, Service-Disabled Veteran-owned, Women Owned Small Business etc…. Further if there are no past performance evaluations on file in the Past Performance Information System Retrieval database, contractors should provide a couple past performance references including the following information: contract numbers, project titles, dollar amounts, points of contact and telephone numbers. Replies should be sent by February 7, 2020, 10:00 am Pacific Time to: Andrew.G.Jacobs@uscg.mil Shortly after receiving responses the Coast Guard will determine if this requirement will be set aside or unrestricted. After the determination a presolicitation notice and request for quote will be posted on this website (www.beta.sam.gov). The NAICS Code is 336611. The small business size standard is less than 1250 employees. Contractors are reminded that in the case of a HUB Zone set-aside, FAR 52.219-3, "Notice of HUBZone Set-Aside or Sole Source Award" would apply which requires that at least 50 percent of the cost of personnel for contract performance be spent for employees of the concern or employees of other HUBZone small businesses. Contractors are also reminded that in the case of a Service-Disabled Veteran-Owned Small Business Set-Aside, FAR 52.219-27, "Notice of Service-Disabled Veteran-Owned Small Business Set-Aside" would apply which requires that at least 50 percent of the cost of personnel for contract performance be spent for employees of the concern or employees of other service disabled veteran owned small businesses. Additionally, regarding FAR 52.219-30 "Notice of Set A-Side For Women-Owned Small Business Concerns…": A women-owned small business (WOSB) concern eligible under the WOSB Program, means a small business concern that is at least 51 percent directly and unconditionally owned by, and the management and daily business operations of which are controlled by, one or more women who are citizens of the United States. Primary Point of Contact: Andrew Jacobs, Andrew.G.Jacobs@uscg.mil Phone: (510) 637-5874
Data sourced from SAM.gov.
View Official Posting »