Inactive Total Small Business Set-Aside (FAR 19.5)

This requirement will be competed as 100% Small Business Set-aside. Award from this solicitation will be made to the responsible offeror whose proposal conforms to all the submission requirements outl... This requirement will be competed as 100% Small Business Set-aside. Award from this solicitation will be made to the responsible offeror whose proposal conforms to all the submission requirements outlined in the instructions to offerors and is determined to provide the best value to the Government, which will evaluate the price and non?cost factors. Technical and past performance factors when combined, are more importance than price. However, pricing can be a factor. a. All offerors shall provide a written statement that all repair work done in accordance with the terms, conditions, and attachments to this solicitation are under a minimum of a 60-day warranty. Failure to provide a warranty statement may result in the proposal not being considered for award. b. All offerors shall fully comply with terms and conditions of the RFQ and address all solicitation requirements to be eligible for award. The solicitation document must be completed in its entirety in order to be compliant with the full solicitation. Offerors that take exception to any term or condition of this RFQ, propose any additional term or condition, or omit any required information may not be considered for award. 2. Completing the RFQ: Please ensure the following information/sections are completed in their entirety: a. Page 1 blocks 17a, 26 (TOTAL OFFER AMOUNT), 30a, 30b and 30c. b. Complete all clauses requiring vendor certifications or information. c. CLIN prices shall be in U.S. Dollars (inclusive of all costs, applicable taxes, and all relevant charges) d. Provide required certifications and documents, per paragraph 3 (below) 70Z08526QIBCT0001 Page 11 of 39 e. Written statement of 60-day warranty Please read the RFQ and all attachments in their entirety. 3. Technical RequirementsAs stated in the Work Specification Document, a technically compliant vendor must submit: a. List of Subcontractors, work items involved, and work site addresses b. Welders Qualifications, including welder's name, type of qualifications, and date of last qualification test c. Written description of Property Control System for GFP d. List of NFPA certified Chemists e. Designation of Competent Person f. List of Qualified Sil-brazers G. Valid Dock side Certifications H. Insurance 4. Past performance a. All offerors must provide two (2) instances of relevant past performance performed within the last three (3) years. This information shall include, but is not limited to:i. Contract Number, Date of Contract Award, and Period of Performanceii. Contact Information for Customeriii. Contract Descriptioniv. Relevant Information 5. To be considered complete, an offer must adhere to the proposal requirements as well as paragraphs 2 and 3, above. A complete offer shall include a detailed description of the vendor's understanding and plan for compliance with the Specification for dockside repairs. 6. The Contracting Officer plans to make an award without discussions. Therefore, the offer should be complete as submitted, include the offerors best price, and shall not include references to data or information previously submitted. Data previously submitted, if any, will not be incorporated "by reference" into the offer and will not be considered in the evaluation of the offer. 7. Clarifications/Questions regarding any aspect of this procurement shall be submitted in writing per ATTACHMENT 4 via email only and addressed to jerrod.a.gonzales@uscg.mil and sandra.a.martinez@uscg.mil no later than 12 PM EST on Oct 28, 2025. Phone calls will not be accepted. The subject line of all email correspondence must state RFQ#70Z08526QIBCT0001 QUESTIONS in the subject line. All questions and responses will be posted via email and on SAM.gov for all potential offerors to review. Any revision to the RFQ as a result of questions and answers will be issued as an amendment to the solicitation. Questions received after this deadline may not be considered. 8. Request for Drawings: The last day to request drawings regarding this solicitation is 12 PM EST on Oct 22, 2025. After this date, further requests may not be accepted due to time constraints. To request drawings, contact jerrod.a.gonzales@uscg.mil and sandra.a.martinez@uscg.mil. All requests should identify the solicitation number RFQ#70Z08526QIBCT0001. Some references listed in the Specification, under "Consolidated List of References," are subject to Export Control limitations or have otherwise restricted distribution and have been deemed "limited access" and "export controlled" packages. In order to access these documents, vendors must be certified as a US or Canadian contractor by the Joint Certification Program (JCP) administered by the Defense Logistic Information Service (DLIS). Instructions and procedures for being certified by JCP can be found at https://www.dla.mil/HQ/LogisticsOperations/Services/JCP/. Only those vendors that have current certification by JCP will be able to be granted explicit access to these packages by the USCG. 9. Responses to this solicitation shall be submitted in writing via email only and addressed to jerrod.a.gonzales@uscg.mil and sandra.a.martinez@uscg.mil no later than 8 AM EST on Nov 06, 2025. Phone calls will not be accepted. The subject line of all email correspondence must state RFQ#70Z08526QIBCT0001 in the subject line. Proposals received after the deadline may not be considered. ANTICIPATED AWARD DATE: The anticipated date of award is on or about Nov 14, 2025.