SLAC National Accelerator Laboratory is requesting a fixed-price quotation for a precision six-axis hexapod positioning system, including a miniature hexapod, hexapod drive, motion controller/development kit, motor and feedback cables, software/calibration support, and on-site startup assistance. An addendum revises the technical evaluation criteria, adding requirements for vertical surface mounting, compact dimensions, specified load and center-of-mass/rotation values, motion ranges, linear/angular accuracy, repeatability, minimum step, in-position stability, active sensor feedback/PID control, cable length, and EPICS/Python API support. Source selection will be based on lowest price and best lead time. The order will be fixed price with NET-30 payment terms and either FOB Destination Prepaid and Add for domestic suppliers or CIP SLAC, Menlo Park, Duty Unpaid for foreign suppliers. Bidders must acknowledge the addendum, provide HTS/ECCN if applicable, register in SAM, complete required representations/certifications (valid for one year unless renewed), and may mark confidential information; on-site field service startup assistance is included.

SLAC National Accelerator Laboratory is operated by Stanford University for the Department of Energy. As a management and operating contractor, subcontracts awarded by the Laboratory are not Federal p... SLAC National Accelerator Laboratory is operated by Stanford University for the Department of Energy. As a management and operating contractor, subcontracts awarded by the Laboratory are not Federal procurements, and are not directly subject to the Federal Acquisition Regulations in 48 CFR. Nonetheless, certain Federal laws, Executive Orders, and regulations may affect our DOE approved purchasing system, as required by statute, regulation, or contract terms and conditions. The follow has been attached for you to complete and review: Requested for Quote: Please provide a price and lead time quotation by 9/18/2026. Technical Evaluation Factors Listed Below: Vertical mounting required (90deg tilted base plate) Attached weight/load: > 3.0 kg (> 6.61 lbs) Load center of mass (CoM): X = -23, Y = -56, Z = 20 Load center of rotation: X = (-56 ... -6), Y = -72, Z = 30 Motion ranges at center of rotation: X, Y ± 50 mm; Z ± 5 mm; ?, ? range 2deg Accuracy - Linear (full travel): < 1 µm* Accuracy - Angular (full travel): 1.939 µrad (0.4 arcsec)* Repeat - Linear (unidirectional): ? 1.5 µm (unidirectional)* Repeat - Angular (unidirectional): 1.939 µrad (0.4 arcsec)* Min Step - Linear: 100 nm Min Step - Angular: 1.939 µrad (0.4 arcsec) In position stability (IPS): < 1 µm & < 2 µrad Active sensor feedback, PID controlled movements and IPS stability Controller & cabling support Cable length ? 10 m Software support: EPICS & Python API, SDK available with purchase Ethernet or USB connection for controls Calibration package for very high accuracy Required item(s) are listed below: HEX150-125HL-4-TAS-PL4 - HEX150-125HL Miniature Hexapod Six-DOF Positioning System (see attached quote) Quantity: 1 EA Automation1-iHXA4-AX6 - Automation1-iHXA4 Hexapod Drive Quantity: 1 EA Automation1-MDK-L1-MA0-LV0-S1-M1 - Automation1-MDK Motion Development Kit Quantity: 1 EA Automation1-iSMC-L1-iHXA4-CP0-H06CM1-HX1-FA0-AP0-DCT0-MA0-IE1-S1-HW0-M2 - Automation1-iSMC Intelligent Software-Based Motion Controller Quantity: 1 EA C26652-100 - Motor cable Quantity: 1 EA Prod-Service-TAS1 - Production Services Configurator Quantity: 1 EA C26651-100 - Feedback cable Quantity: 1 EA GTS-Service-Startup Assistance-1 - GTS Services (on-site field service) Quantity: 1 EA Quote includes the products and services listed above, including on-site startup assistance. Source selection will be based on Lowest Priced Method and best Lead-Time. Please provide a price and lead time quotation by 9/18/2026. Send quote to Cheryl.stafford@slac.stanford.edu. Is there any room for additional discount such as for Academic, ICPT, GSA, or Government Institutions? Buy American Act Certification (BAA) applies to awards over $15,000 unit price. Representations & Certifications Rider is required. Once completed the Reps and Certs is valid for one year until renewal. If you have already completed one within the year please disregard. Otherwise, please complete and return. Please include in your proposals the Harmonized Tariff Schedule (HTS Code) & Export Control Classification Number (ECCN) if applicable. All subcontractors are required to register in the System for Award Management (www.sam.gov). If possible, please provide a link to your webpage for published price list to substantiate for the prices quoted. The resulting purchase order will be issued on a fixed price basis. SLAC National Accelerator Laboratory Terms and Conditions for Fixed Price Commercial Supplies and Services (Rev. August 2023) as well as the SLAC General Terms and Conditions Supplemental Rider (Aug2026_Rev1) will be made a part of the resulting order. Please markup terms and conditions if you wish to negotiate. No mark ups mean that you accept SLAC Terms and Conditions. Payment Terms will be NET-30 Domestic Suppliers - Freight terms will be FOB Destination Prepaid and Add. Foreign Supplier - Shipment will be made CIP SLAC, Menlo Park, and Duty Unpaid. You are requested to mark and identify proprietary/confidential information provided in response to the solicitation. Contact me directly with any questions. Regards, Cheryl Stafford