Inactive

POINT-OF-CONTACT: The point-of-contact for administrative or contractual questions is Contract Specialist Charles Idle at email: Charles.D.Idle@usace.army.mil. Please no phone calls. All questions mus... POINT-OF-CONTACT: The point-of-contact for administrative or contractual questions is Contract Specialist Charles Idle at email: Charles.D.Idle@usace.army.mil. Please no phone calls. All questions must be submitted in writing to the above point-of-contact. OVERVIEW: U.S. Army Corps of Engineers (USACE), Seattle District, requires refurbishment of the two station service units at Chief Joseph Powerhouse. The existing generators have a nameplate rating of 3.0 MVA and the existing turbines are Francis-type units with a nameplate rating of 3,500 HP at 171 feet of head. The following is a list of the major items of work included in this Contract. The work includes the removal of the existing components and systems of components which are known to have lead-based paint, without being specifically identified. The work includes, but is not limited to: General Work Perform all work required for mobilization/demobilization. Remove and dispose of items/systems to be discarded or replaced. Provide platforms, tools and equipment as specified and required to perform the required work. Clean turbine pit, generator, work and storage areas used by the Contractor. Dispose of (recycle) grease, etc. Perform pre outage testing and post reassembly generating unit commissioning. Draft tube fall protection anchors. Mechanical Work Disassemble the generating units and turbines. Inspect and refurbish turbine components. Paint refurbished components. Refurbishment of turbine guide bearings. Provide new Teflon thrust shoes. Refurbish upper and lower generator guide bearings. Furnish bearing RTDs and replace existing RTDs with platinum RTDs. Reassemble generating units. Perform complete alignment of generating units. Perform pre and post refurbishment generating unit operational tests. Disassemble, clean, inspect, refurbish and reinstall all generator brakes and associated appurtenances. Brake ring inspection, with optional refurbishment. Provide new thrust bearing oil coolers. Provide new surface air coolers. Provide new float switches in the bearing tubs. Provide new below the hook lifting devices. Provide new turbine guide bearing coolers. Provide new main cooling water piping and valves. Provide new penstock equalizing and drain valves and piping. Provide new wicket gates. Refurbish the wicket gate servomotors. Inspect the rotor spiders. Electrical Work Rewind the stators. Replace stator cores. Inspect and clean rotors and test the rotor field windings. Optional re-insulation of the rotor field poles. Replace field leads. Replace 4160-volt generator cables. Replace neutral breaker. Perform electrical work related to the installation of bearing RTDs. Perform electrical work related to installation of float switches and other instruments. The magnitude of construction is estimated to be between $10,000,000 and $25,000,000. The resulting contract will be a Firm Fixed-Price contract. The NAICS code for this procurement is 237990, Other Heavy and Civil Engineering Construction, and the associated small business size standard is $39,500,000 in average annual receipts. The solicitation will be issued as Unrestricted. The solicitation documents for this requirement will be issued in electronic format only and will be made available online via the SAM website at www.sam.gov under the subject solicitation number. NO CD's OR HARD COPIES WILL BE AVAILABLE. Offerors are responsible for checking for any update(s) to the Notice/Solicitation. The Government is not responsible for any loss of Internet connectivity or for an offeror's inability to access the document(s) posted at the referenced website. To obtain automatic notifications of updates to this notice, you must log in to sam.gov and add the solicitation to your Watchlist. If you would like to list your firm so others can see you are an interested vendor, you must click the Add Me To Interested Vendors button in the listing for this solicitation on sam.gov. IMPORTANT NOTICE: All contractors proposing on Department of Defense (DoD) solicitations must be registered in the System for Award Management (SAM) database prior to award of a contract. The purpose of this database is to provide basic business information and capabilities to the Government. The SAM website can be accessed at www.sam.gov. Contractors are encouraged to register as soon as possible. All new contracts can be made ONLY to contractors who are registered in SAM. This requirement applies to all DoD contract awards. ACCESS TO SITE VISIT FOR FOREIGN NATIONALS: Processing request for visits by Foreign Nationals can take up to 30 business days to complete and may impact the Contractor’s ability to attend if the paperwork is not approved before the site visit. It is highly recommended that each company plans to have a U.S. Citizen attend the site visit on their behalf. Non-U.S. Citizens and U.S. Citizens wishing to attend the site visit must complete the Request for Visitation Authority form (included in this announcement as an attachment) and submit either a scanned color copy of either the participants passport picture and signature pages or front and back of a driver’s license as soon as possible but no later than noon Pacific Time on 20 December 2021 so it can be processed by USACE Security. The site visit is scheduled for January 6th at 10am. Please submit required documentation for both US Citizen and Non-U.S. Citizens wishing to attend the site visit to Adrienne Murphy, Adrienne.E.Murphy@usace.army.mil (206) 764-6765.

Inactive

FOR INFORMATION ONLY: This Synopsis/Pre-Solicitation Notice is ONLY A NOTIFICATION that a solicitation is anticipated and forthcoming. All questions regarding this Synopsis/Pre-Solicitation should be ... FOR INFORMATION ONLY: This Synopsis/Pre-Solicitation Notice is ONLY A NOTIFICATION that a solicitation is anticipated and forthcoming. All questions regarding this Synopsis/Pre-Solicitation should be submitted in writing via email to Mr. Idle at the email charles.d.idle@usace.army.mil OVERVIEW: U.S. Army Corps of Engineers (USACE), Seattle District, requires refurbishment of the two station service units at Chief Joseph Powerhouse. The existing generators have a nameplate rating of 3.0 MVA and the existing turbines are Francis-type units with a nameplate rating of 3,500 HP at 171 feet of head. The following is a list of the major items of work included in this Contract. The work includes the removal of the existing components and systems of components which are known to have lead-based paint, without being specifically identified. The work includes, but is not limited to: General Work Perform all work required for mobilization/demobilization. Remove and dispose of items/systems to be discarded or replaced. Provide platforms, tools and equipment as specified and required to perform the required work. Clean turbine pit, generator, work and storage areas used by the Contractor. Dispose of (recycle) grease, etc. Perform pre outage testing and post reassembly generating unit commissioning. Draft tube fall protection anchors. Mechanical Work Disassemble the generating units and turbines. Inspect and refurbish turbine components. Paint refurbished components. Refurbishment of turbine guide bearings. Provide new Teflon thrust shoes. Refurbish upper and lower generator guide bearings. Furnish bearing RTDs and replace existing RTDs with platinum RTDs. Reassemble generating units. Perform complete alignment of generating units. Perform pre and post refurbishment generating unit operational tests. Disassemble, clean, inspect, refurbish and reinstall all generator brakes and associated appurtenances. Brake ring inspection, with optional refurbishment. Provide new thrust bearing oil coolers. Provide new surface air coolers. Provide new float switches in the bearing tubs. Provide new below the hook lifting devices. Provide new turbine guide bearing coolers. Provide new main cooling water piping and valves. Provide new penstock equalizing and drain valves and piping. Provide new wicket gates. Refurbish the wicket gate servomotors. Inspect the rotor spiders. Electrical Work Rewind the stators. Replace stator cores. Inspect and clean rotors and test the rotor field windings. Optional re-insulation of the rotor field poles. Replace field leads. Replace 4160-volt generator cables. Replace neutral breaker. Perform electrical work related to the installation of bearing RTDs. Perform electrical work related to installation of float switches and other instruments. The magnitude of construction is estimated to be between $10,000,000 and $25,000,000. The resulting contract will be a Firm Fixed-Price contract. Solicitation number W912DW22R0001 will be posted to the sam.gov website on or about 10 December 2021. The solicitation will be a Request for Proposals. Proposals will be due no sooner than 30 calendar days after actual solicitation issuance date. See the solicitation for details about proposal submission. The NAICS code for this procurement is 237990, Other Heavy and Civil Engineering Construction, and the associated small business size standard is $39,500,000 in average annual receipts. The solicitation will be issued as Unrestricted. A site visit will be offered within approximately 2-3 weeks after the solicitation is made available via sam.gov. Refer to the solicitation for details regarding the site visit. The solicitation documents for this requirement will be issued in electronic format only and will be made available online via the SAM website at www.sam.gov under the subject solicitation number. NO CD's OR HARD COPIES WILL BE AVAILABLE. Offerors are responsible for checking for any update(s) to the Notice/Solicitation. The Government is not responsible for any loss of Internet connectivity or for an offeror's inability to access the document(s) posted at the referenced website. To obtain automatic notifications of updates to this notice, you must log in to sam.gov and add the solicitation to your Watchlist. If you would like to list your firm so others can see you are an interested vendor, you must click the Add Me To Interested Vendors button in the listing for this solicitation on sam.gov. The sam.gov Response Date listed elsewhere in this synopsis is for FBO archive purposes only. It may have no relationship to the actual solicitation due date. The solicitation due date and time will be contained in the solicitation and any solicitation amendments that are issued. IMPORTANT NOTICE: All contractors proposing on Department of Defense (DoD) solicitations must be registered in the System for Award Management (SAM) database prior to award of a contract. The purpose of this database is to provide basic business information and capabilities to the Government. The SAM website can be accessed at www.sam.gov. Contractors are encouraged to register as soon as possible. All new contracts can be made ONLY to contractors who are registered in SAM. This requirement applies to all DoD contract awards. ACCESS TO SITE VISIT FOR FOREIGN NATIONALS: Processing request for visits by Foreign Nationals can take up to 30 business days to complete and may impact the Contractor’s ability to attend if the paperwork is not approved before the site visit. It is highly recommended that each company plans to have a U.S. Citizen attend the site visit on their behalf. Non-U.S. Citizens and U.S. Citizens wishing to attend the site visit must complete the Request for Visitation Authority form (included in this announcement as an attachment) and submit either a scanned color copy of either the participants passport picture and signature pages or front and back of a driver’s license as soon as possible but no later than noon Pacific Time on 19 November 2021 so it can be processed by USACE Security. The site visit is tentatively scheduled for January 6th at 10am. Please submit required documentation for both US Citizen and Non-U.S. Citizens wishing to attend the site visit to Adrienne Murphy, Adrienne.E.Murphy@usace.army.mil (206) 764-6765.

Inactive Total Small Business Set-Aside (FAR 19.5)

Point of Contact: Contract Specialist Charles Idle at charles.d.idle@usace.army.mil US Army Corps of Engineers (USACE), Seattle District, is seeking interested business sources for a construction Proj... Point of Contact: Contract Specialist Charles Idle at charles.d.idle@usace.army.mil US Army Corps of Engineers (USACE), Seattle District, is seeking interested business sources for a construction Project titled: Station Service Primary Component, Chief Joseph Dam, WA. Proposed project will be a firm fixed-price construction project. Construction magnitude is estimated to be more than $10,000,000. 100 percent payment and performance bonds will be required. The North American Industry Classification System (NAICS) code for this project is 237990, Other Heavy and Civil Engineering Construction, and the associated small business size standard is $39,500,000 in average annual receipts. This sources-sought announcement is a tool to identify businesses with the capability to accomplish the work and is for information/market research purposes only. THIS IS NOT A REQUEST FOR PROPOSALS, QUOTATIONS OR BIDS, NOR A SYNOPSIS OF A PROPOSED CONTRACT ACTION UNDER FAR SUBPART 5.2. The type of solicitation to be issued will depend upon information received in response to these sources sought announcement. No reimbursement will be made for any costs associated with providing information in response to these sources sought announcement or any follow up information. Responses to these sources sought announcement will be used by the Government to make appropriate acquisition decisions. NO SOLICITATION IS CURRENTLY AVAILABLE. This is not a request to be placed on a solicitation mailing list and is not to be construed as a commitment by the Government. The results of this survey will be in effect for a period of one year from the date of this notice. Summary Scope of Work (SOW): OVERVIEW: U.S. Army Corps of Engineers (USACE), Seattle District, requires refurbishment of the two station service units at Chief Joseph Powerhouse. The existing generators have a nameplate rating of 3.0 MVA and the existing turbines are Francis-type units with a nameplate rating of 3,500 HP at 171 feet of head. The following is a list of the major items of work included in this Contract. The work includes the removal of the existing components and systems of components which are known to have lead-based paint, without being specifically identified. The work includes, but is not limited to: General Work Perform all work required for mobilization/demobilization. Remove and dispose of items/systems to be discarded or replaced. Provide platforms, tools and equipment as specified and required to perform the required work. Clean turbine pit, generator, work and storage areas used by the Contractor. Dispose of (recycle) grease, etc. Perform pre outage testing and post reassembly generating unit commissioning. Draft tube fall protection anchors. Mechanical Work Disassemble the generating units and turbines. Inspect and refurbish turbine components. Paint refurbished components. Refurbishment of turbine guide bearings. Provide new Teflon thrust shoes. Refurbish upper and lower generator guide bearings. Furnish bearing RTDs and replace existing RTDs with platinum RTDs. Reassemble generating units. Perform complete alignment of generating units. Perform pre and post refurbishment generating unit operational tests. Disassemble, clean, inspect, refurbish and reinstall all generator brakes and associated appurtenances. Brake ring inspection, with optional refurbishment. Provide new thrust bearing oil coolers. Provide new surface air coolers. Provide new float switches in the bearing tubs. Provide new below the hook lifting devices. Provide new turbine guide bearing coolers. Provide new main cooling water piping and valves. Provide new penstock equalizing and drain valves and piping. Provide new wicket gates. Refurbish the wicket gate servomotors. Inspect the rotor spiders. Electrical Work Rewind the stators. Replace stator cores. Inspect and clean rotors and test the rotor field windings. Optional re-insulation of the rotor field poles. Replace field leads. Replace 4160-volt generator cables. Replace neutral breaker. Perform electrical work related to the installation of bearing RTDs. Perform electrical work related to installation of float switches and other instruments. REQUIREMENTS: Interested firms should submit a capabilities package, to include the following: 1. Firm's name, address (mailing and URL), point of contact, phone number, email address. 2. Business classification, i.e., Small Business (SB), Small Disadvantage Business (SDB), Woman-Owned Small Business (WOSB), Veteran Owned Small Business (VOSB), Service Disabled Veteran Owned Small Business (SDVOSB), Historically Underutilized Business Zone (HUBZone) Small Business, 8(a) Program, or Other Than Small Business (large business). 3. Submit three projects that demonstrates Contractor’s ability to meet the scope described in summary scope of work to refurbish the Chief Joseph Dam Station Service Primary Components. Project information submitted shall contain: Project Name/Title; Contract awarded amount; Project location; Project start date; Project completion date; Contractor shall provide a detailed description of the following: The completed projects scope and complexity, how it compares to Chief Joseph’s scope of work, number of units refurbished and CPARs or performance rating. 4. CAGE code and DUNS number. 5. Firm's Joint Venture Information, if applicable. 6. Bonding Information: a. Provide the following, on the bonding company's letterhead: (1) Bonding Limits (a) Single Bond (b) Aggregate All interested parties who believe they can meet the requirements are invited to submit, in writing, complete information describing their interest and ability to meet all requirements stated above. Prior Government contract work is not required for submitting a response under the sources sought announcement. The official Synopsis citing a solicitation number will be issued on Federal Business Opportunities (www.SAM.gov) inviting firms to register electronically to receive an electronic notification of a solicitation should one be issued. SUBMIT TO: Responses to the Sources Sought Announcement should be received no later than 10:00 am (Pacific Time) on 24 September 2021. Submit responses to the attention of Charles Idle, Contract Specialist, by email: charles.d.idle@usace.army.mil. All interested firms must be registered in SAM (https://www.sam.gov) and remain current for the duration of the contract to be eligible for award of Government contracts.