Inactive

CDF Yard Salient Characteristics 9300 24 Port Switch Switch will require at least 24 ports Switch require POE Switch must by CISCO and not be scheduled for EOL/EOS (End of life/End of service) within ... CDF Yard Salient Characteristics 9300 24 Port Switch Switch will require at least 24 ports Switch require POE Switch must by CISCO and not be scheduled for EOL/EOS (End of life/End of service) within the next 3 years. If other than CISCO switches are purchased it will not be compatible with our network and would be unusable. Switch models must be designed for stacking switches as a single virtual switch, enabling customers to have a single management plane and control plane for a maximum of 448 access ports Switch must be able to multicast gateways Switch must have smart licensing and be compatible with the GEMS contract MAXCELL INNERDUCT, 4" 3 CELL, DETECTABLE Must be MaxCell Innerduct, 4" 3 Cell, Detectable, 2650' Reel, Green Corrugated Innerduct Must be High Density Polyethylene Corrugated innerduct, 1-1/2 in., 3500 ft. Must be designed specifically for use with fiber optic cables Must be low weight per foot for easy handling 6 STRAND SINGLE-MODE FIBER OPTIC CABLE Must be 6 Strand Single-mode fiber optic cable Individual fibers are covered with furcation tubing for additional strength Zipties Must be a plastic strip that can be threaded through its end Must be able to tightened so as to fasten something Must be able to bundle cables, wires and tools together for easy storage Self-Laminating Fiber Optic Tag Must be manufactured using rigid vinyl and provides identification in environments where adhesives will not work Must be a rugged, high-quality material is resistant to abrasion and rated for indoor/outdoor use Must be pre-printed with "CAUTION/FIBER OPTIC CABLE/TYPE/COUNT” Must be rated for use up to 176°F (80°C). 3.56" x 2.06" (90.42 mm x 52.32 mm) Color Black/Yellow Conduit measuring tape Must be measuring 3000 ft Must be easy to read markings in sequential one-foot increments Must provide quick and accurate measurement of conduit runs Must be able pull rope through raceways without stretching Measuring tape must not rot or mildew Network Rack Enclosure Must be able to fit a 24-port switch Must have lockable access to front rear & sides Must include pre-assembled parts to includes cage nuts/bolts a shelf hook-and-loop & four keys Must be an enclosure to lock IT equipment inside Must be Flow-through ventilation to keep the equipment cool Must be black Must be wall mountable Must be able to house a patch panel and UPS 12 Port Patch Panel Must be able to plug in 12 ports Panel be able to plug RJ-45 connectors Must be able to remove clutter and organize up to 12 patch cables Fiber Fan Out Kit Must be a Fiber Fan-Out Kit with - 6-Strands 36 inches Must enable you to terminate fiber loose-tube cables Must be able to strip the buffer sheath off the cable and thread each strand through the fan-out assembly Must be color-coded fan-out tubing makes it easy to keep track of your connections Single Mode Lucent Connector Must be able to support all primary fiber types Must be able to reinsert fiber Must be compatible with 250 µm and 900 µm optical fibers, as well as 900 µm, 2 mm and 3 mm cordage Must have no need for hand polishing Must be able to provide a "pass/fail" signal once physical contact is achieved Must be used in fiber optic communications to reduce the optical fiber power by a certain level Single Mode Subscriber Connector Must be a fiber-optic cable connector that uses a push-pull latching mechanism similar to that used in common audio/video cables, which makes it very easy to connect and disconnect the cables. Must be able to mount on 900 micron buffered fiber,1.6 mm jacketed cable and 3.0 mm jacketed cable Must be used in high density applications and not be affected by axial cable loads Heat Shrink Splice Kit Must be able to employ easy to use heat-shrinkable tubing with an adhesive, that when heated forms a semi-flexible moisture proof encapsulation Must make splicing of submersible well pump motor leads easy and water tight Must have connectors and heat shrinkable sleeves Must be used for use on copper tape, wire shield, lead sheath, and UniShield cables Fiber Optic Cleaning Wipes Must be made of lint-free polyester fabric for cleaning bare fiber and connector end-faces, plus optical devices, microscopes, testers, lenses, mirrors and other equipment Heat Shrink Splice Kit Must be made with isopropyl alcohol