Inactive

The U.S Army Contracting Command - New Jersey (ACC-NJ), Picatinny Arsenal, NJ, on behalf of DEVCOM Armaments Center (AC), Munitions Engineering & Technology Center (METC), Fuze and Precision Armaments... The U.S Army Contracting Command - New Jersey (ACC-NJ), Picatinny Arsenal, NJ, on behalf of DEVCOM Armaments Center (AC), Munitions Engineering & Technology Center (METC), Fuze and Precision Armaments Directorate (FPAD) is issuing this sources sought notice as a means of conducting market research to identify potential sources having an interest and capabilities available to support/provide the manufacture, inspection, testing, and delivery of the STINGER M934E6 Fuze and Warhead Body Assembly (Legacy Configuration) and the STINGER Proximity M934E7 Fuze and Warhead Body Assembly with Conformal Antenna. The result of this market research will contribute to determining the method of procurement if a requirement materializes. Based on the responses to this notice, this requirement may be set-aside for small businesses (in full or in part), or procured through full and open competition; or potentially set aside as sole-source in the event only one vendor is determined to be capable of meeting requirements. Multiple awards may be made if determined to be the appropriate strategy. All small business set-aside categories will be considered. Telephone inquiries will not be accepted or acknowledged, and no feedback or evaluations will be provided to companies regarding submissions. DISCLAIMER THIS SOURCES SOUGHT IS FOR INFORMATIONAL PURPOSES ONLY. THIS IS NOT A REQUEST FOR PROPOSAL (RFP) TO BE SUBMITTED. IT DOES NOT CONSTITUTE A SOLICITATION AND SHALL NOT BE CONSTRUED AS A COMMITMENT BY THE GOVERNMENT. RESPONSES IN ANY FORM ARE NOT OFFERS AND THE GOVERNMENT IS UNDER NO OBLIGATION TO AWARD A CONTRACT. NO FUNDS ARE AVAILABLE TO PAY FOR PREPARATION OF RESPONSES TO THIS ANNOUNCEMENT. ANY INFORMATION SUBMITTED BY RESPONDENTS TO THIS NOTICE IS STRICTLY VOLUNTARY. No phone or email solicitations with regards to the status of the RFP will be responded to prior to its release. PROGRAM BACKGROUND The baseline STINGER M934E6 Fuze is a complex electromechanical assembly integrating hybrid microelectronics, advanced inertial and centrifugal components, and electro-explosive devices into a single fuze package. The M934E6 Fuze must interface with the Warhead Body Assembly which forms one of the main structural supports to the missile airframe and consists of a machined Titanium body configured with a Hard Target Sensor (HTS), Radio- Frequency Interference (RFI) Filter and an electrical cable assembly that interfaces between the fuze/warhead and missile sections. The STINGER M934E7 Proximity Fuzes and Warhead Body Assemblies with Antenna are complex electromechanical assemblies integrated with a Radio Detection and Ranging (RADAR) proximity sensor and conformal antenna into the existing baseline STINGER M934E6 Fuze and Warhead Body Assembly configuration. The direct replacement of shelf-life expired legacy configuration fuzes and warhead body assemblies with new Proximity configuration fuzes and warhead body assemblies (with antenna) will enhance the missile capability to engage Unmanned Aerial Systems (UAS) with a Proximity Detonation mode while maintaining the legacy fuzing detonation functions. The STINGER Proximity Fuze and Warhead Body Assembly with Antenna will provide a near miss capability against UAS targets while maintaining all legacy fuze functions against standard STINGER targets. The procurement of the legacy configuration STINGER M934E6 Fuze and Warhead Body Assembly will be in direct support of active and potential Foreign Military Sales (FMS) case requirements. The STINGER M934E7 Fuze and Warhead Body Assembly with conformal antenna must interface with the M258E7 Warhead Section and missile guidance section and flight motor. The M934E6 and M934E7 Fuzes and Warhead Body Assemblies (with and without conformal antenna) are to be Manufactured, First Article and Lot Acceptance tested in accordance with Technical Data Packages as defined in table 1. The U.S. Government anticipates soliciting for offerors located within the National Technology and Industrial Base (NTIB) for single award of a four (4) year, Firm Fixed Price (FFP), Indefinite Delivery Indefinite Quantity (IDIQ) type contract, utilizing a base year with three (3) additional, one (1) year ordering periods, for Fiscal Years 2023 through 2027. The Government encourages responders to provide recommended quantity ranges that are optimal from a price break/economies of scale standpoint to support orders ranging from 90 to 5,000. REQUIRED CAPABILITIES The Government seeks a source to manufacture, inspect, test, and delivery the fuzes and warhead body assemblies, nomenclatures as below, in accordance with the Technical Data Packages identified in table 1. The intent of this Sources Sought is to identify sources and make an assessment of their capability to meet this requirement and develop an appropriate acquisition strategy. The official nomenclatures for the requirements are as follows: Fuze, Guided Missile, M934E6 Warhead Body Assembly Fuze, Guided Missile, M934E7 Warhead Body Assembly, Antenna Table 1 - Technical Data Packages Technical Data Package p/n 9297066, Titled: Fuze, Guided Missile, M934E6 Technical Data Package p/n 9344462, Titled: Warhead Body Assembly Technical Data Package p/n 13052431, Titled: Fuze, Guided Missile, M934E7 Technical Data Package p/n 13051777, Titled: Warhead Body Assembly, Antenna SPECIAL REQUIREMENTS Any resulting contract is anticipated to have a security classification level of Secret. Any resulting contract shall be compliant with the specialty metals restriction of the Berry Amendment (10 U.S.C. 2533a and 2533b) in accordance with DFARS clauses 252.225-7008 and 252.225-7009. ELIGIBILITY The applicable NAICS code for this requirement is 332 -- Fabricated Metal Product Manufacturing/332993 -- Ammunition (except Small Arms) Manufacturing with a Small Business Size Standard of 1,500. The Product Service Code (PSC) is 1390. SUBMISSION DETAILS Interested businesses should submit a brief capabilities statement package (no more than ten 8.5 X 11-inch pages double sided, font no smaller than 10 point). Documentation should be in bullet format. Your response to this notice shall be electronically submitted to the Contracting Officer, Daniel L. Potempa, in either Microsoft Word or Portable Document Format (PDF), via email daniel.l.potempa2.civ@army.mil no later than 3:00 p.m. (EST) on 23 February 2023 and reference this notice number in subject line of e-mail and on all enclosed documents. Information and materials submitted in response to this request WILL NOT be returned. DO NOT SUBMIT CLASSIFIED MATERIAL. Email submittals must be restricted to a maximum file size of 8MB and should be in MSWord or PDF format. If the email submission is larger than 8MB, separate into several emails. Telephone responses will not be accepted. Please address the following in the capabilities statement. 1) Organization name, address, primary points of contact (POCs) and their email address, FAX, Web site address, telephone number, and type of ownership for the organization 2) Appropriate documentation supporting claims of organizational and staff capability. If significant subcontracting or teaming is anticipated to deliver technical capability, organizations should address the administrative and management structure of such arrangements. 3) Demonstrate sufficient production line manufacturing tooling, inspection fixtures, mechanical vibration test equipment with thermal temperature capability, automated computer controlled in-process assembly and Lot Acceptance Test equipment stations (to include test equipment/anechoic capabilities) technical knowledge and expertise required to fulfill the M934E6 and M934E7 Fuze and Warhead Body Assembly (with and without conformal antenna) 4) Anticipated delivery schedule to include all necessary activities related to delivering production lots/quantities (to include FAT and LOT acceptance testing for both proximity and legacy configurations; and any other activities required). 5) If a respondent does not currently have adequate resources (technical, manufacturing, personnel, etc) available, the respondent must detail plans to obtain those resources in a manner that wouldn't adversely impact execution of the contract effort. If a formal solicitation is generated later, a separate solicitation notice will be published. No award will be made as a result of this market survey. All information is to be submitted at no cost or obligation to the Government. All data received in response to this Sources Sought that is marked or designated as corporate or proprietary will be fully protected from any release outside the Government. The information provided will not be returned. The Government reserves the right to reject, in whole or in part, any private sector input as a result of this market survey. The U.S Government is not obligated to notify respondents of the results of this survey. Any documentation provided will not be returned.