Inactive

This notice is a sources sought notice for a requirement at the Portsmouth Naval Shipyard. This notice is being issue to determine interested vendors and to help establish an appropriate set aside if ... This notice is a sources sought notice for a requirement at the Portsmouth Naval Shipyard. This notice is being issue to determine interested vendors and to help establish an appropriate set aside if applicable. Please note that this is NOT a Request For Quote (RFQ) and submission of your company's interest may not result in your company being considered for a set-aside or bidders list for the RFQ. This sources sought notice is for market research purposes only. Vendors that are able to provide this material need to provide the following in an email to Gary.D.Chandler@navy.mil. 1. Vendor's name, address, phone number, fax number, and email address. 2. Vendor's cage code (SAM) 3. Vendor's Size Status (SB, SDVOSB, 8a, HUBZone, WOSB, etc.) 4. If vendor is not the actual manufacturer, the actual manufacturer's name, cage code, and size status. The material is Shaft Sleeves. Specifications are as follows: (2) TRIDENT PROP SHAFT SLEEVES, PC-2 OF DWG 4678498-G, ALL WITH THE FOLLOWING DIMENSIONS: ID TO BE 26.100” + 0” / - 1/16”, OD TO BE 28.500” + 1/16” / - 0”; LENGTH TO BE 14 FT 10” + 1/4” / - 0”. MATERIAL IS TO BE CAST CUNI PER ASTM-B369-09, UNS #C96400 (SUPERSEDING MIL-C-15345, ALLOY 24). RT, PT, VT AND WELDABILITY TESTS ARE REQUIRED. CHEMICAL AND MECHANICAL CERTS ARE ALSO REQUIRED. (2) EA TRIDENT PROP SHAFT SLEEVES, PC-3 OF DWG 4678498-G, ALL WITH THE FOLLOWING DIMENSIONS: ID TO BE 26.220” + 0” / - 1/16”, OD TO BE 28.500” + 1/16” / - 0”; LENGTH TO BE 22-3/4 FT + 1/16” / - 0”. MATERIAL IS TO BE CAST CUNI PER ASTM-B369-09, UNS #C96400 (SUPERSEDING MIL-C-15345, ALLOY 24). RT, PT, VT AND WELDABILITY TESTS ARE REQUIRED. CHEMICAL AND MECHANICAL CERTS ARE ALSO REQUIRED. (2) EA PROP SHAFT SLEEVES, PC-2 OF DWG 4678497-L, ALL WITH THE FOLLOWING DIMENSIONS: ID TO BE 26.250” + 0” / - 1/16”, OD TO BE 28.500” + 1/16” / - 0”; LENGTH TO BE 37-1/2 FT + 1/16” / - 0”. MATERIAL IS TO BE CAST CUNI PER ASTM-B369-09, UNS #C96400 (SUPERSEDING MIL-C-15345, ALLOY 24). RT, PT, VT AND WELDABILITY TESTS ARE REQUIRED. CHEMICAL AND MECHANICAL CERTS ARE ALSO REQUIRED. NOTE: FOR ALL ITEM 0001 SLEEVES ABOVE, ROUNDNESS OF THE ID’S IS TO BE WITHIN 0.015” AND CONCENTRIC TO THE OD’S WITHIN 1/32”. STRAIGHTNESS OF THE LENGTH OF ALL SLEEVES IS TO BE WITHIN 0.010”. PRIOR TO START OF MANUFACTURE THE VENDOR MUST SUBMIT THEIR NDT PROCEDURES WITH ACCEPTANCE CRITERIA TO PNSY CODE 135T FOR REVIEW AND APPROVAL. IF ANY WELD REPAIRS NEED TO BE DONE ON ANY OF THE SLEEVES, VENDOR MUST FIRST SUBMIT THEIR WELDING PROCEDURE TO PNSY CODE 138, AS WELL AS APPLICABLE NDT PROCEDURES NOT ALREADY APPROVED TO CODE 135T, FOR REVIEW AND APPROVAL PRIOR TO ANY WELDING BEING DONE.