HOSES
The Defense Logistics Agency (DLA) Maritime Norfolk at Norfolk Naval Shipyard (NNSY) intends to award a Firm Fixed Price (FFP) Single Award Contract with Lowest Price Technically Acceptable (LPTA) and... The Defense Logistics Agency (DLA) Maritime Norfolk at Norfolk Naval Shipyard (NNSY) intends to award a Firm Fixed Price (FFP) Single Award Contract with Lowest Price Technically Acceptable (LPTA) and Delivery Schedule Evaluation Factors for the item listed below. The required item is for commercial items prepared in accordance with the information in FAR Part 13 and FAR Subpart 12.6, as supplemented with the additional information included in this notice. The Contract Line Items (CLINs) are as follows: CLIN 0001 2.5 INCH SUCTION AND DISCHARGE HOSE, 2.5 INCH FEMALE CAMLOCK AND 2.5 INCH MALE CAMLOCK ... 50 FT SECTIONS QTY: 30 ASSEMBLY Heavy duty, hard wall, suction, and discharge hose. Hose shall consist of nitrile/corrugated wrapped finished. Inner most tube shall be nitrile, reinforced with multiple textile plies and a dual wire helix. The hose inner liner (tube) and outer cover shall be BLACK in color. The color shall be thoroughly embedded into the reinforcement and helical wire(s) to provide a homogeneous hose wall and result in sufficient adhesion to meet the required hose application of the follow: 2-1/2” I.D. X 3” O.D. HOSE MUST HAVE A WORKING PRESSURE OF 150 PSI (MINIMUM) AND 250 PSI (MAXIMUM). HOSE MUST NOT EXCEED A BURST TEST PRESSURE OF 800 PSI. MUST HAVE A MINIMUM BEND RADIUS OF 2.5” 1.40 – 1.50 LBS. MAXIMUM WEIGHT PER FOOR WITHOUT COUPLING. HOSE SHALL BE CAPABLE OF TAKING A FULL VACUUM. MUST BE RESISTANT TO WEATHER, OIL, SOLVENTS, AND MILD ACIDS HOSE MUST HAVE A TEMPERATURE RATING OF -40 DEGREES (F) TO + 180 DEGREES (F). HOSES ARE TO BE PROVIDED IN 50 FOOT LENGTHS (+12” / -12”) HOSE MUST HAVE A MALE COUPLING (AA59326/2A-7-B) ON ONE END AND A FEMALE HOSE COUPLING (AA59326/6A-7-B) ON THE OTHER END. FITTINGS MUST BE RED BRASS ALLOY C84400. NOTE: EACH COUPLINGS SHALL BE PERMANTLY/MECHANICALLY ATTACHED BY EXTERNAL CRIMPING, UTILIZING A STAINLESS STEEL CRIMP FERRULE IN ACCORDANCE WITH COUPLING MANUFACTURER’S RECOMMENDATION. EACH HOSE ASSEMBLY SHALL HAVE, AT A MINIMUM, THE MFG’S NAME, CONTRACT NUMBER AND PRESSURE RATING ON LAYLINE IN PERMANENT INK OR MOLDED INTO COVERING. SUPPLIER MUST PROVIDE WRITTEN CERTIFICATION THAT HOSE ASSEMBLIES (HOSE AND FITTING) HAVE BEEN HYDROSTATICALLY TESTED AT 150 PSIG WITH CLEAN, FRESH WATER FOR 10 MINUTES WITH ZERO LEAKS, WEEPS, END FITTING SLIPPAGE AND/OR BULGES. HOSE SHALL BE PARKER SWC609 OR EQUIVALENT AT NO COST TO THE GOVERNMENT, NORFOLK NAVAL SHIPYARD RESERVES THE RIGHT TO REQUEST A SAMPLE ASSEMBLY FOR TESTING AND EVALUATION PURPOSES FROM ANY OR ALL OFFERORS DURING EVALUATION PROCESS. HOSE MUST BE PALLETIZED OFFERORS SPECIFICATIONS SHALL BE REVIEWED PRIOR TO AWARD. CLIN 0002 2.5 INCH SUCTION AND DISCHARGE HOSE, 2.5 INCH FEMALE CAMLOCK AND 2.5 INCH MALE CAMLOCK ... 25 FT SECTIONS QTY: 32 ASSEMBLY Heavy duty, hard wall, suction, and discharge hose. Hose shall consist of nitrile/corrugated wrapped finished. Inner most tube shall be nitrile, reinforced with multiple textile plies and a dual wire helix. The hose inner liner (tube) and outer cover shall be BLACK in color. The color shall be thoroughly embedded into the reinforcement and helical wire(s) to provide a homogeneous hose wall and result in sufficient adhesion to meet the required hose application of the follow: 2-1/2” I.D. X 3” O.D. HOSE MUST HAVE A WORKING PRESSURE OF 150 PSI (MINIMUM) AND 250 PSI (MAXIMUM). HOSE MUST NOT EXCEED A BURST TEST PRESSURE OF 800 PSI. MUST HAVE A MINIMUM BEND RADIUS OF 2.5” 1.40 – 1.50 LBS. MAXIMUM WEIGHT PER FOOR WITHOUT COUPLING. HOSE SHALL BE CAPABLE OF TAKING A FULL VACUUM. MUST BE RESISTANT TO WEATHER, OIL, SOLVENTS, AND MILD ACIDS HOSE MUST HAVE A TEMPERATURE RATING OF -40 DEGREES (F) TO + 180 DEGREES (F). HOSES ARE TO BE PROVIDED IN 25 FOOT LENGTHS (+12” / -12”) HOSE MUST HAVE A MALE COUPLING (AA59326/2A-7-B) ON ONE END AND A FEMALE HOSE COUPLING (AA59326/6A-7-B) ON THE OTHER END. FITTINGS MUST BE RED BRASS ALLOY C84400. NOTE: EACH COUPLINGS SHALL BE PERMANTLY/MECHANICALLY ATTACHED BY EXTERNAL CRIMPING, UTILIZING A STAINLESS STEEL CRIMP FERRULE IN ACCORDANCE WITH COUPLING MANUFACTURER’S RECOMMENDATION. EACH HOSE ASSEMBLY SHALL HAVE, AT A MINIMUM, THE MFG’S NAME, CONTRACT NUMBER AND PRESSURE RATING ON LAYLINE IN PERMANENT INK OR MOLDED INTO COVERING. SUPPLIER MUST PROVIDE WRITTEN CERTIFICATION THAT HOSE ASSEMBLIES (HOSE AND FITTING) HAVE BEEN HYDROSTATICALLY TESTED AT 150 PSIG WITH CLEAN, FRESH WATER FOR 10 MINUTES WITH ZERO LEAKS, WEEPS, END FITTING SLIPPAGE AND/OR BULGES. HOSE SHALL BE PARKER SWC609 OR EQUIVALENT AT NO COST TO THE GOVERNMENT, NORFOLK NAVAL SHIPYARD RESERVES THE RIGHT TO REQUEST A SAMPLE ASSEMBLY FOR TESTING AND EVALUATION PURPOSES FROM ANY OR ALL OFFERORS DURING EVALUATION PROCESS. HOSE MUST BE PALLETIZED OFFERORS SPECIFICATIONS SHALL BE REVIEWED PRIOR TO AWARD. The requirement will be solicited as a total small business set-aside. The NAICS code applicable to this procurement is 326220, Rubber and Plastics Hoses and Belting Manufacturing. The Product Service Code is 4720. The anticipated delivery date for this acquisition is 10 business days ARO. The solicitation, any documents related to this procurement, and all amendments issued will be in electronic form only. THE SOLICITATION IS NOT YET AVAILABLE. The solicitation number is SPMYM123Q0069 and it is expected to be available on or about 28 July 2023 and posted to SAM.gov, https://sam.gov/ Quotes will be due by 5:00 PM EST on 04 August 2023. Responses to the solicitation notice shall be emailed to the attention of Monica Richardson at monica.richardson@dla.mil. Please make sure that the solicitation number (SPMYM122Q0069) is included in the subject line of any email correspondence. Emails without subject lines will not be read because of security issues. Potential offerors are hereby notified that the solicitation and any subsequent amendments will only be available by downloading the documents at www.SAM.gov (Contracting Opportunities). The Government is not responsible for inability of the Offerors to access solicitation documents posted. Prospective Offerors should also register on the interested vendor list under SPMYM122Q0069. No telephone or FAX requests will be accepted, and no hardcopy solicitation/amendment will be mailed or faxed. All responsible sources may submit a proposal which may be considered by the Government. By submitting a quote, the offeror will be self-certifying that neither the principal corporate officials nor owners are currently suspended, debarred, or otherwise ineligible to receive contracts from any federal agency. Failure to do so may represent grounds for refusing to accept the proposal. By submission of a proposal, the offeror acknowledges the requirement that a prospective awardee must be registered in the System for Award Management (SAM) database prior to award, during performance, and through final payment of any contract resulting from the solicitation, except for awards to foreign vendors for work to be performed outside the United States. Lack of registration in the SAM database will make an offeror ineligible for award. Offerors may obtain information on registration and annual confirmation requirements by calling 1-866-606-8220, or via the Internet at https://www.sam.gov. All questions shall be submitted in accordance with the solicitation, dates and procedures. Please direct all questions regarding this requirement to Monica Richardson at monica.richardson@dla.mil.
Links ()
Attachments ()
Data sourced from SAM.gov.
View Official Posting »