Anchor Cable - 1710-00-605-2937
This notice was posted to identify sources that can manufacture NSN 1710-00-605-2937 and are interested in quoting a solicitation. This notice was posted for the purpose of market research only and is... This notice was posted to identify sources that can manufacture NSN 1710-00-605-2937 and are interested in quoting a solicitation. This notice was posted for the purpose of market research only and is not a Request for Proposal (RFP). Please review the NSN below and provide any sources that may be able to manufacture the item. The sources that are currently approved to manufacture this Cable Anchor are listed below. If you are interested in this requirement, please complete the attached Market Research Questionnaire. All information should be submitted to the Contract Specialist, Kyle Barr, at kyle.barr@dla.mil no later than May 22, 2024. The approved sources and part numbers are listed below: 2M490 – Nassau Tool Works (P/N: 606170-3) 0BVP9 – Capy Machine Shop (P/N: 606170-3) 20722 – The Entwistle Company (P/N: 606170-3) 20075 – Bosch Rexroth (P/N: 606170-3) “NOTE: This project contains Drawings/Specifications. Vendors may access the applicable drawings/specifications by querying SPE7M224R0019MR within the solicitation field at the following link: https://pcf1.bsm.dla.mil/cfolders. Drawings cannot be accessed through a DIBBS, cFolders link at this time.” The following requirements are necessary for the completion of manufacturing of this item: Cable Anchor 82N ALRE CSI SERIALIZATION: Serialization is required for this ALRE CSI part as well as the packaging for traceability. Contractor technical documentation shall reflect the appropriate marking scheme. All serialized and lot numbered CSI parts shall be accounted for; to include material scrapped during manufacturing. Re-branding by suppliers which obscures the original marking (part number, serial number, CAGE) of the OEM of ALRE CSI parts is prohibited. Please notify DLA Contracting Officer at time of quote if serialization is not practical due to size, material property, unreasonable or excessive cost. RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES RQ039: Non-Tailored Higher-Level Quality Requirements (SAE AS9100) for Manufacturers and Non-Manufacturers RQ040: Non-Destructive Testing (NDT) Accreditation Requirements RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. The Government Procuring Activity has determined that Surplus is not Acceptable for this NSN. (End of TQ Requirement) SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS; AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA. PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR MERCURY COMPOUND. (IAW NAVSEA 5100-003D). AIRCRAFT LAUNCH AND RECOVERY EQUIPMENT (ALRE) CRITICAL APPLICATION ITEM SOURCE APPROVAL - TO BE ELIGIBLE FOR AWARD UNDER THIS SOLICITATION, AN OFFEROR MUST BE AN APPROVED SOURCE OR PROVIDE THE PRODUCT OF AN APPROVED SOURCE AS DETERMINED BY THE ENGINEERING SUPPORT ACTIVITY, NAVAL AIR WARFARE CENTER (NAWC) AIRCRAFT DIVISION LAKEHURST. THE CRITERIA AND PROCEDURES FOR SOURCE APPROVAL ARE CONTAINED IN PART I OF THE NAVAL INVENTORY CONTROL POINT (NAVICP) PHILADELPHIA BROCHURE ENTITLED "SOURCE APPROVAL INFORMATION BROCHURE FOR SPARES". THE LATEST VERSION OF THIS BROCHURE MAY BE OBTAINED BY ACCESSING NAVICP'S WEBSITE: HTTPS://WWW.NAVSUP.NAVY.MIL, OUR TEAM, NAVICP, BUSINESS OPPORTUNITIES, COMMODITIES, SOURCE APPROVAL REQUEST (SAR) BROCHURE SPARES TO ASSIST IN THE DETERMINATION OF SOURCE APPROVAL, THE OFFEROR MAY BE REQUIRED TO SUBMIT TO A SURVEY PRIOR TO AWARD IN WHICH NAWC LAKEHURST MAY PARTICIPATE. IN ADDITION, THE OFFEROR MUST PROVIDE THE FOLLOWING INFORMATION, WHICH MAY BE CONSIDERED IN DETERMINING WHETHER THE OFFEROR IS AN APPROVED SOURCE: (1) A SOURCE APPROVAL LETTER FROM NAVICP'S ENGINEERING AND PRODUCT SUPPORT DIRECTORATE; OR; (2) OTHER EVIDENCE INDICATING THAT THE OFFEROR MEETS THE SOURCE APPROVAL CRITERIA. ALL REQUESTS FOR WAIVERS OR DEVIATIONS CLASSIFIED AS CRITICAL, MAJOR, OR MINOR MUST BE FORWARDED TO THE DSC CONTRACTING OFFICER FOR REVIEW AND APPROVAL. ALL ITEMS OF SUPPLY SHALL BE MARKED IAW MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE), CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S CAGE CODE AND PART NUMBER. (February 2016) THIS MATERIAL MUST MEET NAVAIR AIRCRAFT LAUNCH & RECOVERY EQUIPMENT TRACEABILITY REQUIREMENTS. BARE ITEM MARKINGS SHALL BE IAW THE TECHNICAL DATA DRAWINGS PROVIDED. BARE ITEM MATERIAL SHALL BE MARKED WITH CONTRACT NUMBER, NAWC CAGE, AND PART NUMBER UNLESS OTHERWISE SPECIFICIED ON ASSOCIATED DRAWING. IF A CONFLICT EXISTS WITH MARKING REQUIREMENTS OF THIS 82N ALRE/SE ITEM, THE ASSOCIATED DRAWING REQUIREMENTS SHALL APPLY. NOTE: THIS IS A RESTRICTED SOURCE ITEM AND REQUIRES ENGINEERING SOURCE APPROVAL BY THE GOVERNMENT DESIGN CONTROL ACTIVITY. RD002, COVERED DEFENSE INFORMATION APPLIES RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. UNLESS OTHERWISE SPECIFIED, THE FOLLOWING CDRLS APPLY: -First Article Testing Report -Production Test and Inspection Report -Certificate of Quality Compliance -Test Report for Radiographic Inspection CLAUSE 52.246-15, CERTIFICATE OF CONFORMANCE, IS NOT AUTHORIZED FOR THIS NSN. Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies. CRITICAL APPLICATION ITEM BOSCH REXROTH CORPORATION 27005 P/N 606170-3 CAPY MACHINE SHOP INC. 0BVP9 P/N 606170-3 NASSAU TOOL WORKS, INC 2M490 P/N 606170-3 THE ENTWISTLE COMPANY LLC 20722 P/N 606170-3 IAW REFERENCE DRAWING NR 80020 606170 REVISION NR K DTD 10/29/2002 PART PIECE NUMBER: 606170-3 IAW REFERENCE DRAWING NR 80020 217612 REVISION NR E DTD 06/26/2005 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 D88933 REVISION NR 22 DTD 02/21/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 217388 REVISION NR F DTD 05/02/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 217613 REVISION NR F DTD 05/22/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 315417 REVISION NR H DTD 05/22/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 315418 REVISION NR K DTD 03/01/2004 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 315420 REVISION NR F DTD 06/04/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 315421 REVISION NR H DTD 06/04/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 315422 REVISION NR G DTD 06/04/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 315423 REVISION NR G DTD 06/04/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 502252 REVISION NR M DTD 11/04/2002 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 A91843 REVISION NR 19 DTD 07/23/2002 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 B88933 REVISION NR 28 DTD 04/08/2004 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 87750 REVISION NR 25 DTD 02/21/2023 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 55-31817 REVISION NR M DTD 03/27/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 87757 REVISION NR 11 DTD 06/29/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 87762 REVISION NR 16 DTD 02/22/2011 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 C88963 REVISION NR 34 DTD 03/21/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 A89816 REVISION NR 31 DTD 05/20/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 16236 CN006052937 REVISION NR DTD 01/25/2024 PART PIECE NUMBER: IAW REFERENCE QAP 16236 SQAP006052937CFAT REVISION NR DTD 01/25/2024 PART PIECE NUMBER: IAW REFERENCE QAP 16236 SQAP006052937QA REVISION NR DTD 01/25/2024 PART PIECE NUMBER: IAW REFERENCE QAP 16236 CDRL-006052937-23356 REVISION NR DTD 12/22/2023 PART PIECE NUMBER:
Data sourced from SAM.gov.
View Official Posting »