Pump, Hydraulic, Push-Start
Federal Business Opportunities (FedBizOpps) Synopsis Information Form 1. ACTION CODE: ( X ) P = Presolicitation ( ) M = Modification to a Previous Presolicitation Notice 2. CLASSIFICATION CODE: 4320 3... Federal Business Opportunities (FedBizOpps) Synopsis Information Form 1. ACTION CODE: ( X ) P = Presolicitation ( ) M = Modification to a Previous Presolicitation Notice 2. CLASSIFICATION CODE: 4320 3. NAICS CODE: 333996 4. TITLE: Pump, Hydraulic, Push-Start 5. RESPONSE DATE: May 4, 2020 6. PRIMARY POINT OF CONTACT: Morgan Stein 7. SOLICITATION NUMBER: SPE7M120Q0621 9. DESCRIPTION: Pump, Hydraulic, Push-Start RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/HQ/LogisticsOperations/EnhancedValidation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. Exceptions to DWG: CAGE: 2G657 PN:51-75101-3041-4 is approved NOTE: THE CITED DRAWING IS A SOURCE CONTROLLED DRAWING AND AS OF THE DATE OF THIS SOLICITATION ONLY THE SOURCE(S) CITED ON THE DRAWING HAVE BEEN APPROVED. EVEN THOUGH SOURCES AND APPROVED PART NUMBERS ARE PROVIDED, THE ITEMS FURNISHED MUST MEET THE REQUIREMENTS OF THE CITED DRAWING. OFFERORS WHO ARE INTERESTED IN QUALIFYING THEIR PRODUCT FOR PURPOSE OF FUTURE ACQUISITION MUST CONTACT THE COGNIZANT DESIGN ACTIVITY SPECIFIED ON THE SOURCE CONTROLLED DRAWING. ALSO, MAY INCLUDE ADDITIONAL APPROVED SOURCES THAT HAVE NOT BEEN REFLECTED ON THE DRAWING AT THIS TIME. NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE INCLUDING DATA FOR THE APPROVED AND ALTERNATE PART FOR EVALUATION. THIS NSN SHALL BE PHYSICALLY IDENTIFIED I/A/W MIL-STD-130. RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN SINCE THIS NSN IS A NAVY FIELD LEVEL REPARABLE ITEM CONFIGURATION CONTROL MUST BE MAINTAINED PER MIL-STD-973. CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. CRITICAL APPLICATION ITEM Ronal Industries, Inc. 2G657 P/N 51-75101-3041-4 IAW BASIC DRAWING NR 80064 2601125 REVISION NR D DTD 06/15/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80064 2589373 REVISION NR A DTD 03/11/1982 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80064 2584064 REVISION NR G DTD 11/17/1993 PART PIECE NUMBER: IAW REFERENCE QAP 80064 2589142 REVISION NR D DTD 09/03/2019 PART PIECE NUMBER NSN(s): 4320-01-420-1169 Item Description: Rotary Pump Parts Kit Manufacturer's Code and Part Number (if applicable): CAGE: 0UBG9 PN: JPG-0483-2 Quantity (including option quantity): 26 EA Unit of Issue: EA Destination Information: Inspection and Acceptance at Origin / FOB Origin Delivery Schedule: 236 Days All responsible sources may submit an offer/quote which shall be considered. ( X ) The solicitation will be available in FedBizOpps on its issue date of __April 2, 2020___________. ( X ) This acquisition is for supplies for which the Government does not possess complete, unrestrictive technical data; therefore, the Government intends to solicit and contract with only approved sources under the authority of 10 U.S.C. 2304(c)(1). Approved sources are: Curtiss-Wrigh Electro-Mechanical (0UBG9), PN: JPG-0483-2 ( X ) While price may be a significant factor in the evaluation of offers, the final award decision will be based upon a combination of price, delivery, past performance and other evaluation factors as described in the solicitation. Based upon market research, the Government is not using the policies contained in Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice. The proposed contract action is for supplies for which the Government intends to solicit and negotiate with only one source under the authority of FAR 6.302. Interested persons may identify their interest and capability to respond to the requirement or submit proposals. This notice of intent is not a request for competitive proposals. However, all proposals received within forty-five days (thirty days if award is issued under an existing basic ordering agreement) after date of publication of this synopsis will be considered by the Government. A determination by the Government not to compete with this proposed contract based upon responses to this notice is solely within the discretion of the Government. Information received will normally be considered solely for the purpose of determining whether to conduct a competitive procurement. 10. TYPE OF SET-ASIDE Total
Data sourced from SAM.gov.
View Official Posting »