Inactive Total Small Business Set-Aside (FAR 19.5)

The Contractor shall furnish all labor, materials, equipment and supervision to replace the Fogged window glass panels located in the Control Tower Cab (see attached drawing that identifies the four u... The Contractor shall furnish all labor, materials, equipment and supervision to replace the Fogged window glass panels located in the Control Tower Cab (see attached drawing that identifies the four units to be replaced) in the McCain Control Tower. The units to be replaced are labeled #4, #9,#11 and #12 as reflected on Drawing A-104 (attached). The Contractor will be required to visit the McCain Control Tower indicated to field measure, and verify the dimensions, type glass and installation requirements required to replace the Glass unit. A safety plan indicating work procedures, size of cranes or other lift equipment required for this work shall be provided to the Contracting Officer for approval. Specifications and Additional details shall be listed in the following sections. Note: Due to strict Airfield requirements the Control Tower Window replacement work shall be scheduled and coordinated with Air Operations and the Contracting Officer. The work shall be performed after normal working hours. The Airfield is normally closed on Saturdays. The Contractor will be required to furnish sufficient man power and equipment to complete the Glass replacement on the day scheduled. All electronic equipment inside the tower shall be protected at all times and at no time shall the opening be left open unsupervised or to inclement weather. McCain Air Field Control Tower: Replace (4) Control Cab insulated window units. The new units shall consist of two (2) lites of ½” annealed glass separated by a ½” bronze air spacer. The primary Glass shall be type 1, Quality Q3, meeting federal specification ASTM C-1036. The insulated unit shall be fully sealed at perimeters. The unit shall include Capillary tubes to equalize pressure inside units. Units shall be designed to reduce exterior noise to 30 db inside tower cab. The window shall also be designed to resist 120 mph wind loading, and have a light transmissivity of 85%. During installation all cleaners, primers or sealants shall be type recommended by the gasket manufacture. The new windows shall be installed and sealed not allowing any water or air infiltration in building. At completion the new window units shall be cleaned inside and out by the installer.

Inactive Total Small Business Set-Aside (FAR 19.5)

1. GENERAL DESCRIPTION Aerial spraying for vegetation control at Sea Ray Target Range at Shugualak, MS (420 acres). The work shall be located at Sea Ray Target Range at Shugualak, MS. The Contracting ... 1. GENERAL DESCRIPTION Aerial spraying for vegetation control at Sea Ray Target Range at Shugualak, MS (420 acres). The work shall be located at Sea Ray Target Range at Shugualak, MS. The Contracting Officer will indicate the exact location. The work to be performed under this contract consists of the application of herbicides for vegetation control Sea Ray Target Range shall comprise of 420 acres for application of herbicides for vegetation control. This location work shall be accomplished between the months of March - May 2020. The herbicide vegetation mix shall be in compliant with Federal and state guidelines for aquatic and wooded areas. All application mixes and application shall be in accordance with manufacture instructions. Also, any adjuvant and surfactant needed to increase effectiveness shall be added to the herbicide. Contractor shall furnish all labor, supervision, tools, materials, equipment, and transportation necessary to perform the site preparation work as identified. When it is determined by the Contracting Officer that the original areas, or portions thereof, are unsuitable or unavailable for performance of the specified work, the Contracting Officer reserves the right to delete areas or to substitute, at the contract price, the same type and amount of work (+/- 10%) in other areas similar in topography and conditions within NAS Meridian. Aerial Site Preparation . Contractor shall have a result of at least 85% kill rate on all vegetation no matter what herbicide combination is used. Contractor shall conduct any necessary kill rate until accepted by government (PWD). The aerial spraying will be with a helicopter and all flight requirements will be coordinated with Naval Air Stations Meridian’s Air Operations. Application operations shall not be started or continued if wind is in excess of 5 MPH, or if rain is expected within 2 hours. b. Quality Assurance Evaluator (QAE). The Government employees designated to monitor contractor performance for this job is PWD FEAD. 23b. Water is limited at Sea Ray Target Range. A residential type (garden hose) from a well water source is available. Contractor shall provide all necessary supplemental equipment, material and labor for water for this location.