Inactive Total Small Business Set-Aside (FAR 19.5)

22 APRIL 2024 8:52 AM EST -- Clarification made to SPEC 3.1.5. The electrical drawing/schematic shall be delivered along with with the delivery of the 8010 Damage Control Conex Box. The drawing/schema... 22 APRIL 2024 8:52 AM EST -- Clarification made to SPEC 3.1.5. The electrical drawing/schematic shall be delivered along with with the delivery of the 8010 Damage Control Conex Box. The drawing/schematic should include a wiring diagram of sufficient detail that would allow for replacement/maintenance/procurement of components if required, such as gauge of wire, lead labelling for all components (inlet connector, fused disconnect, transformer, electrical distribution box, and power outlet), part numbers, etc. Vendors should confirm this deliverable when submitting the bid. 18 APRIL 2024 7:00 AM EST -- Solicitation updated to more clearly state the delivery date of this procurement and to post a vendor inquriry and Government response. Delivery shall be made to the Naval Submarine Base, New London, CT (actually located in Groton, CT) on or before 07 AUGUST 24. QUESTION: The AC unit is on a sliding shelf. Is there a P/N or drawings to build the shelf? GOVERNMENT RESPONSE: The Government does not have a part number or drawing for the air conditioning sliding bracket. Design and manufacture of the bracket to allow for storage of the air conditioning unit during transport is the responsibility of the contractor. 16 APRIL 2024 3:05 PM EST -- Solicitation amended to extend the due date of quotes to 26 APRIL 2024 at 5 p.m. EST. 15 APRIL 2024 12:37 PM EST -- Additional photo of the outside of the container has been uploaded. Plus a response to a vendor inquiry: QUESTIONS: -What are requirements for the breaker box, i.e., assuming 100A Box, spare breakers? -What is insulation requirements (R-rating, type of insulation)? -What type of flooring material is desired? -Are there pictures of the outside? GOVERNMENT RESPONSE: “The flooring will be a standard wood flooring of the contractors choice. The walls and ceiling will be in accordance with spec. The contractor is to provide an electrical drawing in accordance with the spec. The breaker shall be in accordance with enclosure 2 of the spec. Please see the pictures in enclosure 2. The insulation shall be a closed cell spray foam with an R-5 or higher rating. The unit shall be similar to the attached photo.” 12 APRIL 2024 2:04 PM EST -- Solicitation updated to post a vendor question and the Government response. QUESTION: "We wanted to clarify if you want us to provide the cabinets along with the container, or if you would be installing them to meet your requirements" GOVERNMENT RESPONSE: "The container should come outfitted with the cabinets installed". 09 APRIL 2024 3:03 PM EST -- Solicitation updated to correct the PSC code (from PSC code 5998 to PSC code 4240). This is a solicitation for a non-commercial supply procurement. Supervisor of Shipbuilding, Groton intends to award a firm fixed price (FFP) purchase order, for the procurement of QTY. One (1) 8010 Compliant Damage Control Conex Box with Delivery made to the Naval Submarine Base, New London, located in Groton, Connecticut on or before 07 August 2024. Solicitation Number: N62789-24-Q-0005 is issued as a Request for Quotation (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular, FAC-2024-03, with an effective date of 23 February 2024. This procurement is a 100% small business set aside. NAICS CODE: 332311 Size Standard: 750. CLIN 0001: Manufacture QTY. One (1) 8010 Compliant Submarine Rapid Response Damage Control Conex Box, in accordance with the below requirements. The reference/plans are attached to this solicitation as separate documents. 2. REFERENCE/PLANS: 2.1 Enclosure (1), Electrical Distribution Diagram 2.2 Enclosure (2), Existing Layout Pictures 2.3 Enclosure (3), DC Conex Box 2.4 S0570-AC-CCM-010/8010, Industrial Ship Safety Manual for Fire Prevention and Response 3. REQUIREMENTS: 3.1 The Contractor shall provide ONE (1) new condition 20 foot x 8 foot ISO Shipping Container (CONEX Box), manufactured to be 8010 compliant, in accordance with references 2.1 through 2.4, and the following requirements: 3.1.1 The Contractor shall install insulation on the walls and roof of the conex box. 3.1.2 The Contractor shall line walls and ceiling of the conex box with three-quarter inch (3/4)” white face Melamine. 3.1.3 Power input shall be a 480VAC, 30A, 3-pin Leviton P/N 330B7WLEV connector. 3.1.4 Power Outlet to other (existing) boxes shall be a 120/240VAC, 60A 4 pin Leviton P/N 460R12WLEV connector. 3.1.5 The contractor shall develop and provide an electrical drawing/schematic for the 8010 DC Conex Box. 3.1.6 All measurements have an allowable tolerance of plus or minus 1 ½ inches. 3.1.7 The air conditioning unit shall be able to slide into the unit for transport and slide out of the unit and be able to drain while in operation. 3.1.8 The power strip along the workbench shall have 12 outlets. 3.1.9 The power strips along the shelves (Qty 4) shall have 8 outlets. 3.1.10 The Conex Box shall have forklift slots on both sides. 3.1.11 The Contractor shall paint exterior of the conex box victory red. Color code number: 9B1922 (or equivalent). 3.1.12 The Contractor shall label the conex box with the weight of the conex box in the as built configuration. CLIN 0002: Shipping. Contractor shall Deliver/Ship to (FOB Destination) one (1) ISO Container conex box. Delivery must be accomplished between Monday - Friday between 0700 and 1330 EST. Delivery location is as follows: SUB BASE NEW LONDON CT NSSF NLON, R6-25D ATTN: GARY DUNN BLDG 17 2ND DECK, AMBERJECK ROAD LOWER SUBMARINE BASE Groton, CT 06340 M/F: Jim Crudden Phone: 860-694-2424 CONTRACTOR TO PROVIDE A QUOTE BROKEN DOWN IN THE FOLLOWING MANENR: $X.XX – CONEX BOX $X.XX – SHIPPING $X.XX – TOTAL COST The Government will evaluate the total offers for award purposes by adding the total price for all line items. Evaluation of all line items will not obligate the Government to award all line items. The Government intends to evaluate the quotes and award a contract without discuss ion offerors. However, the Government reserves the right to conduct discussions if later determined by the Contracting Officer to be necessary. Quotations are due prior to 5:00 p.m. EST, 22 APRIL 2024. Late submissions will not be accepted. Offers should be submitted via electronic commerce. The electronic address for receipt of offers is: Andrea.a.cook.civ@us.navy.mil. Offerors should identify the RFQ number in the subject line of the email. Offerors are advised to submit electronic documents early and confirm successful transmission/receipt. The System for Award Management (SAM) is a Government maintained database of companies wanting to do business with the Government. A firm must register and have an active registration in SAM in order to receive a federal award. Register at: https://sam.gov/SAM/pages/public/index.jsf The Government reserves the right to award one line item, all line items or any combination thereof. If multiple line items are awarded, costs/prices for each line item will be totaled and the award amount will be based on that total. The Award will be made to the responsible offeror, whose offer, conforming to the solicitation, is determined to be the best overall value; price and other factors considered. In determining the best overall response, the combined non-cost/price factors are more important than the cost/price factor; however, cost/price remains a significant factor. The Government may select for award the offeror whose price is not necessarily the lowest, but whose technical proposal is more advantageous to the Government and warrants the additional cost. Offerors must satisfy the requirements described in the performance criteria (see also attached specification and corresponding references), as well as other RFQ requirements. Offers that take exception to any performance criteria are unacceptable.