Inactive Total Small Business Set-Aside (FAR 19.5)

Specfications: RCRS/EMD Vehicle Lease Vacuum Truck Wet/Dry TANK- -3,000 USG, 78" Diameter -0.3125 SA516-70 Shell & Head Material -Operating Temperature Range -20 to 200 Degrees F -Internal Pressure 15... Specfications: RCRS/EMD Vehicle Lease Vacuum Truck Wet/Dry TANK- -3,000 USG, 78" Diameter -0.3125 SA516-70 Shell & Head Material -Operating Temperature Range -20 to 200 Degrees F -Internal Pressure 15 PSIG, External Pressure 15PSIG (Full Vacuum) -2" Brass Pressure Relief set at 15PSI -One (1) Anti Surge Baffle Mounted on Reinforced Pads. -External Circumferential Reinforcement Rings with Tank Support Feet -8" Internal Shut Off with 12" SS Float Ball and Cage Assembly with Neoprene Rubber Seat -Liquid Level Gauge, SS Constructed Rotary Float Gauge with 6" Float Ball Assembly Located on Front Drivers Side with Grab Handle and Up Position Tie Back -Full Length Hydraulic Dump Sub-Frame, 20 Ton 3 Stage Single Acting Dump Cylinder, Rear Dump Pivot Assembly & Safety Brace -Hydraulic Full Opening Rear Door Assembly with 6 Heavy-Duty Door Bolts, Neoprene Rubber Rear Door Gasket, Dual Double Acting Side Mounted Hydraulic Cylinder and Safety Brace -Hydraulic Vibrator Mounted Bottom of Tank with Reinforcing Pad, Heavy Duty Mounting Channel and Pressure Relief Valve VALVES- -Isolation Valve: 8” Air Operated Butterfly Valve Between Primary and Cyclone with PTO Interconnect -Suction Valve, 6" Manually Operated Brass Valve with 6" Sand Pipe/Deflector Plate Assembly, Aluminum Kamlok Fitting with Dust Cap Mounted on Rear Head. -Discharge Valve, 6" Manually Operated Brass Valve with 6" Sand Pipe/Deflector Plate Assembly, Aluminum Kamlok Fitting with Dust Cap Mounted on Rear Head. -Loading Nozzle, 6” Rear Loading Nozzle with Wear Sleeve and Aluminum Kamlok Fitting with Dust Cap Mounted on Rear Head BOOM- -6” Moro hydraulic boom with 320 degree hydraulic rotation, 4 ft. hydraulic extension, isolation valve and remote pendent VACUUM BLOWER- -Roots DVJ 1021 Blower 5184 CFM free air rating, 4100 CFM @ 18"Hg, 27"Hg maximum vacuum -Drive: Driven by Air Shift Transfer Case -Piping: Dual 8" Diameter with 8" Quick Disconnect Rubber Boot Assembly -Valving: 6" Manual Butterfly Vacuum Relief Valve and 12" In-Line Check Valve Assembly FILTRATION SYSTEM- -Dual 42” Diameter Steel Bag House Assembly with 29-4” x 59” Acrylic Coated Bags, Oil/Moisture Repellent, Air Cannon Pulsation with Hydraulic Lift Cylinder and Hold Down Clamps. -Dual 20" Diameter Cyclones Mounted on 20" Diameter Drop Box with Side Swing Clean Out, 3" Brass Drain Valve and Aluminum Kamlok Fittings with Dust Caps -Cusco 30” Diameter Final Filter Assembly Installed for Protection of Blower with 20 ”Diameter Stainless Steel 100 Micron Filter PRESSURE UNLOADING- -Moro PM80 Air Cooled Vacuum/Pressure Pump (350 CFM free air 28" Hg) Hydraulically Driven From 6 Bolt Air Shift PTO -3" Air Operated Isolation Butterfly Valve -3" Diameter No Disconnect Piping -4" Secondary Moisture Trap and Muffler/Oil Trap HYDRAULICS- -Hydraulic Oil Resevoir Mounted on Dump Sub-Frame with Suction Strainer, Diffuser, Fill Cap, Hydraulic Oil Filters and Sight Glass. -4-Spool Valve Body for Control of Dump, Rear Door, Filtration System, Vibrator and Pressure Unloading System GAUGES- -Gauge Panel with Tank Vacuum/Pressure Gauge, Hydraulic Pressure Gauge and Filter Element Vacuum Gauge SIDE TRAYS- -Full-length Carbon Steel Side Boxes for Hose Storage/Fender Assembly with Anti-Sail Mud-Flaps and Rear Tire Skirt TRIM- -12” Walkway, Full Length on Driver Side with Safety Railing and Ladder. Fold Down Rail for Boom to Operate on Driver Side -(4) Numbered Placards -Ladder Assembly -50' Static Line -Steel Toolbox Assembly 24"w x 18"d x 18"h DOT LED LIGHTING- -(3) lamp rear module assembly, Clearance lamps, Reflectors -(3) Row Clearance Markers, (2) Rear Halogen Flood Lights, (1) Rear Amber Strobe Beacon BUMPER- -DOT Rear Bumper for Protection of External Valves with Platform/Step Assembly and Rear Dirt Shield PAINT- -Entire Tank and Body of the Vacuum System shall be Sandblasted and Receive (2) Coats of Primer (2) Coats of Single Stage Axalta Paint -Tank to be White, Equipment to be Black - Any Deviation will be at Additional Cost CHASSIS FEATURES MAKE Peterbilt MODEL 567 ENGINE Cummins ISX 425 HP TRANSMISSION Automatic FRONT AXLE: 20,000# REAR AXLE 40,000# w/ Peterbilt AirTrac Pusher Axle: 13.5 steerable pusher Wheels: Polished Aluminum