Inactive

Inactive

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|||||||||||||||||||| HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT|8|x|||||||| TIME OF DELIVERY (JUNE 1997)|20||||||||||||||||||||| STOP-WORK ORDER (A... ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|||||||||||||||||||| HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT|8|x|||||||| TIME OF DELIVERY (JUNE 1997)|20||||||||||||||||||||| STOP-WORK ORDER (AUG 1989)|1|| WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|INVOICE AND RECEIVING REPORT (COMBO)|N/A|TBD|N00383|TBD|TBD|SEE SCHEDULE|TBD||||||||| NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1|WSS PHILADELPHIA| VALUE ENGINEERING (JUN 2020)|3|||| EQUAL OPPORTUNITY (SEP 2016)|2||| SMALL BUSINESS SUBCONTRACTING PLAN (DOD CONTRACTS)- BASIC (DEC 2019)|2||| INTEGRITY OF UNIT PRICES (NOV 2021)|1|| WARRANTY OF SUPPLIES OF A NONCOMPLEX NATURE (JUN 2003)|6|12 MONTHS|60 DAYS AFTER DISCOVERY OF DEFECT||||| WARRANTY OF DATA - BASIC (MAR 2014)|2||| SMALL BUSINESS SUBCONTRACTING PLAN (OCT 2022)|4||||| EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2||| TRANSPORTATION OF SUPPLIES BY SEA (JAN 2023)|2||| FIRST ARTICLE APPROVAL--CONTRACTOR TESTING (SEP 1989)|10||||||||||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM - BASIC (JAN 23)|3|||| LIMITATION OF LIABILITY--HIGH-VALUE ITEMS (FEB 1997)|1|| LIMITATIONS ON PASS-THROUGH CHARGES (JUN 2020)|1|| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (NOV 2020)|13|||||||||||||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (DEC 2022))|3|||| BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (NOV 2014)|1|| ROYALTY INFORMATION (APR 1984)|1|| ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2023)|13|336413|1250|||||||||||| FACSIMILE PROPOSALS (OCT 1997)|1|| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||X| EVALUATION OF FIRST ARTICLE TESTING|3|||| This solicitation is for made new manufacture spare parts. This is a sole source requirement. The Government physically does not have inits possession sufficient, accurate, or legible data to contract with other than the current source. These items require Government Source Approval prior toaward. If you are not an approved source, you must submit, together with your proposal, the information detailed in the NAVSUP WSS Source Approval Brochure which can be obtained on the internet at https://www.navsup.navy.mil/public/navsup/wss/business_opps/. Offers received which fail to provide all data required by the source approval brochure will not be considered for award under this solicitation. For information or questions regarding this notice, please contact Kristin Clemens at the email address: kristin.clemens2.civ@us.navy.mil. NAVSUP WSS Requests proposals submitted in response to this solicitation remainvalid for a minimum of 120 days following submission. All contractual documents related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile, or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein. \ 1. SCOPE 1.1 . Markings shall be in accordance with MIL-STD-130. 1.2 Sampling rates (AQLs) indicated below shall be used in accordance with ANSI Z1.4 for Single Sampling and a General Inspection Level of II. 1.3 In addition to the 100% PCO Mandatory, critical and major characteristics, attributes for plating, hardness and non-destructive testing will be inspected one hundred percent. 1.4 Contractor shall develop a system for identification of individual piece parts for traceability purposes. Markings shall not be permanent. 1.5 An AQL of 1.5 will be used for Class 3 threads and dimensions, and geometric feature controls with a tolerance range of .010 or less. 1.6 For minor characteristics, a sampling rate determined by the contractor and subject to QAR approval will be used. 1.7 PRE-AWARD / POST AWARD REQUIREMENTS: Due to the critical use of this item and its quality history, a pre-award survey and post-award conference may be required for all new manufacturers. For all previous sources, a post-award conference may be recommended. 1.8 . The contractor shall include on the detailed process/operation sheets developed, (1) all in house manufacturing processes and (2) the identity of all manufacturing sources performing processes/operations outside their facility. These sheets shall not be revised or altered after the successful completion of First Article or Production Lot Testing without approval from the Basic Design Engineering activity, via the PCO. 1.9 . Unless otherwise specified, for fabricated parts, the Inspection Method Sheets/ Final Inspection Sheets shall list the characteristics of each item produced under the contract. The manufacturer shall be required to provide certifications of all raw material including castings and forgings. the material source shall be identified and the documentation shall be able to identify the customer and/or contract number. The manufacturer shall maintain all raw material documentation for a minimum of ten (10) years. The contractor is responsible for providing completed Inspection Method Sheets/Final Inspection Sheets showing the actual dimensions taken for ALL Characteristics,in addition, critical characteristics shall be annotated. 1.10 The material covered in this contract/purchase order will be used in a crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital shipboard systems or loss of aircraft. Therefore,the material has been designated as Critical material and special control procedures are invoked to ensure receipt of correct material. 1.11 The components being acquired under this solicitation have been classified as Flight Critical requiring engineering source approval by the Naval Air Systems Command. Only those companies who have submitted requests for source approval and been approved will be eligible for award under this solicitation. Any company not previously approved may submit a Source Approval Request to the contracting officer, Naval Inventory Control Point, (See Block 10 of the SF33 for name and code). The Source Approval Request shall contain the following documentation and shall be submitted by the closing date of this solicitation: (A) Copy of complete configuration drawings for a similar item(s) which your company has produced within the past three years, including test procedures for which your company (1) has been qualified to manufacture and (2) which is similar, i.e., requires the same materials, manufacturing processes, inspections, tolerances and similar application as the item(s) for which you are seeking approval. (B) Copy of the complete process/operation sheets used to manufacuture the similar item, including but not limited to, detailed shop sketches. These plans must note those operations and processes performed by subcontractors/ vendors. (C) Complete copies of purchase orders, shipping documents, etc. that document delivery of production quantities of the part to the Original Equipment Manufacturer or Military service. Provide the most recent copies of the documents. (D) A detailed comparative analysis of the differences/similarities between the similar part and the part(s) for which you are seeking approval. This analysis should include materials, configuration, tolerances, process requirements, dimensions, castings, forgings, etc. (E) Copy of inspection method sheets used in the manufacturing and at final inspection. These sheets should include actual tolerance, print requirements, inspection devices, sources performing the operation and level of inspection. Critical characteristics should be discernible from all other characteristics. The above requirements are a subset of requirements specified in the ASO Source Approval Information Brochure dated January 1995. The submission of this data subset is contingent upon and in consideration of the submitting contractor meeting all other requirements specified in this solicitation to include a bilateral agreement with MDA which includes availability of complete data, MRB disposition, etc. Any company not having such agreement, but desiring to seek engineering source approval, will be required to submit data meeting all requirements of the ASO/NAVICP Source Approval Brochure. 1.12 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWC LAKEHURST; drawing number ( ;613665-3; ) ;80020; , Revision ;P; and all details and specifications referenced therein. 1.13 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification. 1.14 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C. 2. APPLICABLE DOCUMENTS DRAWING DATA=A414463 |80020| V| |A| | | | DRAWING DATA=A91477 |80020|23| |A| | | | DRAWING DATA=B414463 |80020| Y| |A| | | | DRAWING DATA=MPR1222 |80020| A| |A| | | | DRAWING DATA=MPR1223 |80020| C| |A| | | | DRAWING DATA=323201 |80020| E| |A| | | | DRAWING DATA=416325 |80020| H| |A| | | | DRAWING DATA=416334 |80020| G| |A| | | | DRAWING DATA=416451 |80020| M| |A| | | | DRAWING DATA=416540 |80020| H| |A| | | | DRAWING DATA=416543 |80020| P| |A| | | | DRAWING DATA=416574 |80020| D| |A| | | | DRAWING DATA=416578 |80020| K| |A| | | | DRAWING DATA=416618 |80020| D| |A| | | | DRAWING DATA=416620 |80020| D| |A| | | | DRAWING DATA=416621 |80020| F| |A| | | | DRAWING DATA=416622 |80020| G| |A| | | | DRAWING DATA=416623 |80020| F| |A| | | | DRAWING DATA=416631 |80020| H| |A| | | | DRAWING DATA=510941 |80020| L| |A| | | | DRAWING DATA=511228 |80020| L| |A| | | | DRAWING DATA=511229 |80020| F| |A| | | | DRAWING DATA=511230 |80020| L| |A| | | | DRAWING DATA=511231 |80020| J| |A| | | | DRAWING DATA=511232 |80020| J| |A| | | | DRAWING DATA=511234 |80020| M| |A| | | | DRAWING DATA=511235 |80020| P| |A| | | | DRAWING DATA=613665 |80020| P| |A| | | | DRAWING DATA=613881 |80020| J| |A| | | | 3. REQUIREMENTS - NOT APPLICABLE 4. QUALITY ASSURANCE 4.1 Review documentation as provided under DD 1423 requirements. 4.2 CRITICAL MANUFACTURING PROCESSES ( ;APPLIES; ) HEAT TREAT ( ;APPLIES; ) WELDING ( ;N/A; ) CADMIUM PLATING ( ;N/A; ) ENGINEERING CHROME PLATING ( ;N/A; ) NICKEL CHROME PLATING ( ;N/A; ) CASTING(S) ( ;N/A; ) FORGING(S) ( ;APPLIES. MPR1222, MPR1223; ) MPR (MATERIAL PROCESSING REQUIREMENTS) 4.3 SPECIAL INSPECTION REQUIREMENTS ( ;APPLIES; ) MAGNETIC PARTICLE INSPECTION ( ;APPLIES; ) SURFACE INSPECTION ( ;APPLIES; ) PENETRANT INSPECTION ( ;N/A; ) RADIOGRAPHIC INSPECTION ( ;N/A; ) ULTRSONIC INSPECTION ( ;N/A; ) HIGH SHOCK TEST ( ;N/A; ) MECHANICAL VIBRATION TEST 4.4 FINAL INSPECTION REQUIREMENT:Due to the critical nature of this item, representatives of the buying office/and the cognizant field activity, NAWC Lakehurst, shall be notified by the successful contractor at least 14 days prior to presentation to the DCM QAR of the items for final inspection so that they may have the option of witnessing the final inspection. The contractor shall notify by email or TELEFAX PCO and NAWC Lakehurst QA ;ROY JANNEY NAWC QA REP AT FAX (732) 323-4986; to arrange for the final inspection.The authority of the QAR shall not be abrogated. If the notification is not given to both sites then the QAR shall not accept the units. 4.5 . Mandatory Inspection Requirements: 100% Procurement Contracting Officer (PCO) mandatory inspection is required and shall be accomplished at source under the surveillance and final approval of the cognizant DCMAO Quality Assurance Representative (QAR). During production, mandatory inspection is required to be accomplished by the contractor as follows: A. Level of Inspection (LOI). 1. Critical characteristics: 100% inspection shall apply. 2. Major and Minor characteristics: LOI shall be in accordance with a sampling plan acceptable to the QAR. B. Critical characteristics: ;ALL ACTUAL DIMENSIONS ARE TO BE RECORDED. RECORD TIME AND AMBEINT TEMPERATURE WHEN MEASUREMENTS ARE TAKEN. CERTIFICATIONS TO BE ON FILE FOR MINIMUM OF SEVEN YEARS AFTER DELIVERY OF CONTRACT.; C. Major and Minor characteristics 1. Shall be defined by the contractor subject to QAR concurrence, unless defined on applicable drawings and associated specifications. 4.6 The test to be performed under the First Article approval clause (FAR 52.209-3) of the contract are listed below 4.6.1 Dimensional test (special) ;CLOSE MACHINE TOLERANCES; 4.6.2 Requirements of: ;LKE DRAWING PACKAGE; 4.6.3 Form ;APPLIES; 4.6.4 Fit ;N/A; 4.6.5 Function ;APPLIES. HYDROSTATIC TEST PER DWG. 613665; 4.6.6 Compliance with drawing ( ;80020; ) ;613665; , Revision ;P; and specifications referenced therein. 4.7 In addition to the above tests, the First Article(s) to be inspected hereunder shall also be subjected to those tests which will demonstrate that the article(s) comply with the contract requirements 4.8 The contractor shall be responsible for providing the necessary parts and repair of the First Article Sample(s) during inspection 4.9 The contractor shall notify the PCO, ACO, and QAR fourteen (14) days prior to conducting the First Article test so that the Government may witness such testing. 4.9.1 The QAR shall be present to witness all First Article Testing. 4.9.2 The following additional personnel shall witness the First Article Testing: ;ROY JANNEY NAWC QA REP AT FAX (732) 323-4986; 4.10 Disposition of FAT samples 4.10.1 ; ; Sample(s) may be destroyed during testing. 4.10.2 ;APPLIES; Unless otherwise provided for in the contract, sample(s) shall remain at the contractor and may be considered as production items under the contract provided the sample(s) can be refurbished to ready for issue condition and provided the sample(s) have inspection approval of the cognizant DCMC QAR. Sample(s) may be shipped as production items only after all other units required under the contract have been produced and are ready for shipment. 4.11 Test Sample Coating Instructions 4.11.1 Samples are to be unpainted. Corrosive areas are to be coated with a light preservative if required. 4.12 Notice to Government of Testing at the contractors facility. 4.12.1 FAR 52.209-3 applies (A) The contractor shall present ;ONE; ; unit(s) of the following CAGE( ;80020; ; ), Part Number ;613665-2; ; , Revision ;P; ; as specified in this contract. At least fourteen (14) calendar days before the beginning of the First Article testing, the contractor shall notify the contracting officer, in writing, of the time and location of the testing so that the Government may witness the tests. (B) The contractor shall submit the First Article Test Report within 15 calendar days from the date of testing to: ;PCO; ; The contractor shall mark the report "First Article Test Report" and cite the contract number and lot/item number. Review documentation as provided under the DD1423 requirements. (C) Within 45 calendar days after the Government inspects the First Article, the contracting officer shall notify the contractor, in writing, of the approval, conditional approval, or disapproval of the First Article. The notice of approval, conditional approval, or disapproval shall not relieve the contractor from complying with all requirements of the specifications and all other terms and conditions of this contract. A notice of conditional approval shall state any further action required of the contractor. A notice of disapproval shall cite reasons for disapproval. (D) If the First Article is disapproved, the contractor, upon Government request shall repeat any or all First Article Tests. After each request for additional tests, the contractor shall make any necessary changes, modifications, or repairs to the First Article or select another First Article for testing. All costs related to these tests are to be borne by the contractor, including any and all costs for additional tests following a disapproval. The contractor shall then conduct the tests and deliver another report to the Government under the terms and conditions and within the time specified in paragraph B above. The Government reserves the right to require an equitable adjustment of the contract price for any extension of the delivery schedule or for any additional costs to the Government related to these tests. (E) If the contractor fails to present any First Article on time, or the contracting officer disapproves any First Article, the contractor shall be deemed to have failed to make delivery within the meaning of the default clause of this contract. (F) Unless otherwise provided in the contract, and if the approved First Article is not consumed or destroyed in testing, the contractor may deliver the approved First Article as part of the contract quantity if it meets all contract requirements for acceptance. (G) If the Government does not act within the time specified in paragraph (C) above the contracting officer, shall, upon timely written request from the contractor, equitably adjust under the Changes clause of this contract the delivery or performance dates and/or the contract price, and any other contractual term affected by the delay. (H) Before First Article Approval, the acquisition of materials or components for, or the commencement of production or, the balance of the contract quantity is at the sole risk of the contractor. Before First Article approval, the costs thereof shall not be allocated to this contract for 1) progress payments, or 2) termination settlements if the contract is terminated for the convenience of the Government. The contractor is responsible for providing operating and maintenance instructions, spare parts, and repair of the First Article during any First Article test. (I) The contractor shall produce both the First Article and the production quantity at the same facility and shall submit a certification to the effect with each First Article. (J) The test report (2 copies) shall be in accordance with MIL-STD-831, unless otherwise specified on the DD1423, and shall be submitted via the cognizant DCMC to NAVSUP, ATTN: (Cite name and code in Block 10.a of the SF33). The DCMC shall provide comments on Form DD1222 (2 copies) which shall be forwarded with the test report. Approval of the test report is the PCO's responsibility. Upon notification of approval, condition approval, the ACO shall execute the DD250 to indicate Government acceptance of the test report. 4.13 Alternate Offers - Waiver of First Article Approval Requirements. (The following provisions supersede any waiver of First Article Approval Requirements terms set forth in clause 52.209-3 or 52.209-4 as appropriate) (A) Unless otherwise specified in the solicitation, NAVSUP WSS reserves the right to waive the First Article Approval Requirements specified herein for offerors who have previously furnished identical production articles accepted by the Government or the Original Equipment Manufacturer/Prime Manufacturer. An offeror requesting waiver of First Article Requirements shall submit evidence with its offer establishing that: (I) the last production unit was delivered within three (3) years of the issue date of this solicitation, and (II) the production location to be used for this requirement is the same as used for the previous production run. Additionally, the offeror shall submit a certification, to be executed by the officer or employee for the offer, stating that: (I) the articles to be provided will be produced using the same facilities, processes, sequences of operations and approved subcontractors as those previously delivered and accepted by the Government or the Original Equipment Manufacturer/Prime Manufacturer, and (II) the previous production units were manufactured without Material Review Board disposition or waiver/deviation request or rejection of pre-production samples for cause. (NOTE: This certification concerns a matter within the jurisdiction of an agency of the United States and the making of a false, fictitious, or fraudulent certification may render the maker subject to prosecution under Title 18, United States Code, Section 1001.) (B) Offerors requesting waiver of First Article Approval Requirements under the provisions of this clause are cautioned to submit two prices for articles required herein - one that is based on compliance with the First Article Approval Requirements and one that is based on a waiver of such requirements. Where an offeror submits only one price and fails to clearly state that the price is based on waiver of the First Article Approval Requirements it will be deemed to be based on compliance with the First Article Approval Requirements (C) In the event of the First Article Approval Requirement is granted, the delivery schedule for the production items shall be reduced by the number of days designated for delivery of First Article Test unit plus the number of calendar days indicated for the government notification of conditional approval or approval. These requirements are specified in the quality assurance section of this solicitation. If the offeror is unable to meet the desired schedule, he shall insert below the alternate delivery schedule he offers to the government. Offeror's Proposed Alternate Delivery Schedule (Based on waiver of First Article Approval Requirements) Within Days: Item No. _____________ Quantity:_______ After Date of Contract:_________ 5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE 6. NOTES - NOT APPLICABLE THIS IS A ALRE CRITICAL APPLICATION ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET. (NAVSUP REFERENCE ONLY: 22-10083) THE COMPONENTS BEING ACQUIRED UNDER THIS SOLICITATION HAVE BEEN CLASSIFIED AS "CRITICAL" REQUIRING ENGINEERING SOURCE APPROVAL BY THE NAVAL AIR SYSTEMS COMMAND. ONLY THOSE COMPANIES WHO HAVE SUBMITTED REQUESTS FOR SOURCE APPROVAL AND BEEN APPROVED WILL BE ELIGIBLE FOR AWARD UNDER THIS SOLICITATION ANY COMPANY NOT PREVIOUSLY APPROVED MAY SUBMIT A SOURCE APPROVAL REQUEST AS OUTLINED LATER IN THIS SOLICITATION. NAWCADLKE ALRE Engineering - Steam Catapults Comments: NOTE: TDR FOR REPAIR/OVERHAUL ONLY OF PN 613665-2, NGL TENSIONER CYLINDER ASSEMBLY OVERHAULING ACTIVITY SHALL SUBMIT THEIR OVERHAUL AND INSPECTION PROCEDURE TO NAWCADLKE ALRE ENGINEERING VIA REQUEST FOR ENGINEERING INFORMATION(REI) FORREVIEW AND APPROVAL. NOTE: TDR FOR REPAIR/OVERHUAL OF PN 613665-2 ONLY. OVERHAULING ACTIVITY SHALL SUBMIT THEIR OVERHAUL AND INSPECTION PROCEDURE TO NAWCADLKE ALRE ENGINEERING VIA REQUEST FOR ENGINEERING INFORMATION (REI) FOR REVIEW AND PPROVAL OVERHAUL TO BE PERFORMED IN ACCORDANCE WITH NAVAIR 51-15ABB-4.1, NAVAIR 51-15ABB-4.2, NAVAIR 51-15ABB-4.2, NAVAIR 51-15ABD-2, AND ALL DRAWINGS REFERENCED ON TDR USED FOR THIS REPAIR ORDER. DATE OF FIRST SUBMISSION=200 DAC block 6: forward additional copy to aso code cited in block 10.A on page 1. ALL CERTIFICATIONS, TEST REPORTS, AND IN-PROCESS INSPECTION DOCUMENTS NEEDED TO SUBSTANTIATE PRODUCT QUALITY SHALL BE AVAILABLE WHEN PRESENTED FOR FIRST ARTICLE INSPECTION AT CONTRACTORS FACILITY. NOTIFICATION OF 14 PRIOR TO PRESENTATION FOR INSPECTION MUST BE GIVEN TO ROY JANNEY NAWC QA (732) 323-1381 REQUIREMENTS FOR (80020) 613665 REV"P" DRAWING PACKAGE: -DIMENSIONAL INSPECTION PER DWGS. 613665,323201,A414463,B414463,416325,416334 416451,416543,416574,416578,416620,416621,416622,416631,510941,511229,511228 (AFTER COATING),416623,416618,416540,511230,511231,511232,(AFTER COATING), 511234,511235,613881, AND A914477. -PART IDENTIFICATION PER DWGS. 613665,511234,416325,416334,416578,416620, 416622,511229,511228,511230,511231,511232,613881 AND A91477. -MATERIAL AND MAIL CERTIFICATION PER DWGS. 613665,323201,A414463,B414463,416325 416334,414451,416543,416574,416578,416620,416621,416622,416631,510941,511229 511228,416623,416618,416540,511230,511231,511232,511234,511235,613881 & A91477 -HYDROSTASTIC TEST IAW NOTE 2 PER DWG 613665 -VERIFY ASSEMBLY IAW ASSEMBLY PROCEDURES NOTES 1,2,3 & 4 PER DWG. 613665 -VERIFY REQUIREMENTS OF NOTE 1 PER DWG. A414463 -VERIFY PLATING PER DWG. A414463 & B4414463 -MAGNETIC PARTICLE INSPECTION PER DWG. A414463,B414463,416622,416623,416540, 511232 AND A91477 -VERIFY REQUIREMENTS OF NOTE 13 PER DWG. A414463 -VERIFY REQUIREMENTS OF NOTE 11 PER DWG. B414463 -VERIFY REQUIREMENTS OF NOTE 18 PER DWG. B414463 -HEAT TREAT PER DWG. 416334,416622 AND 416463 -HARDNESS TEST PER DWG. 416334,416622, AND 416623 -COATING IAW NOTE 4 DWG. 416334,416621 -VERIFY REQUIREMENTS OF NOTE 7 PER DWG. 416543 -COATING IAW NOTE 2 PER DWG. 416620 -COATING IAW NOTE 5 DWG. 416622 -VERIFY THAT THREADS ARE NOT GROUND IAW NOTE 8 PER DWG. 416622 -VERIFY WELDING IAW NOTE 4 PER DWG. 510941.511232 AND 613881 -HEAT TREAT 510941-2 PRIOR TO HEAT TREAT PER DWG. 510941 -HARDNESS TEST 510941-2 PER DWG. 510941 -MAGNETIC PARTICLE INSPECTION 510941-2 PRIOR TO WELDING IAW NOTE 8 PER DWG 510941 -MAGNETIC PARTICLE INSPECTION 510941-1 PRIOR TO AND AFTER (ASTM E1444 PARA 6.1.4.3) PLATING IAW NOTE 8 PERDWG. 510941. 510941 -MAGNETIC PARTICLE INSPECTION 510941-1 PRIOR TO AND AFTER (ASTM E1 E1444 PARA 6.1.4.3) PLATING IAW NOTE 8 PER DWG. 510941 -ASSEMBLE PER DWG. 511229,511234, AND 511235 -COATING IAW NOTE 8 PER DWG. 511228 -PENETRANT INSPECTION PER DWG. 511231 -COATING IAW NOTE 7 PER DWG. 511232 -HYDROSTATIC TEST IAW NOTE 10 PER DWG. 511232 -VERIFY VENDOR SUBSTANTIATION OF REQUIREMENTS OF NOTE 3 IAW NOTE 6 PER DWG. 511234 -VERIFY VENDOR SUBSTANTIATION OF REQUIREMENTS OF NOTE 3 IAW NOTE 7 PER DWG. 511235 -COATING IAW NOTE 6 PER DWG. 613881 -VERIFY REQUIREMENTS OF NOTE 4 PER DWGS A91477 -100% INSPECT AND RECORD THE READINGS FOR THE PITCH DIAMETER;AND DOCUMENT THAT THE INSPECTION RESULTS FOR THE FUNCTION SIZE IAW SYSTEM 22 OF FED-STD-H28/20 ARE ACCEPTABLE PER DWG. 511228,511232,511234,A414463,B414463 -COPIES OF ALL APPROVED DEVIATION AND WAIVERS UNIQUE REQUIREMENTS: P/N 511235 IS A SOURCE CONTROLLED DRAWING, AND CAN BE PROCURED ONLY FROM APPROVED SOURCES OF SUPPLY, PER DWG. 511235. DATE OF FIRST SUBMISSION=ASREQ block 6: forward additional copy to aso code cited in block 10.A on page 1. ALL CERTIFICATIONS,TEST REPORTS, AND IN-PROCESS INSPECTION DOCUMENTS NEEDED TO SUBSTANTIATE PRODUCT QUALITY SHALL BE AVAILABLE WHEN PRESENTED FOR FINAL INSPECTION. REQUIREMENTS FOR (80020) 613665 REV"N" DRAWING PACKAGE: -DIMENSIONAL INSPECTION PER DWGS. 613665,323201,A414463,B414463,416325,416334 416451,416543,416574,416578,416620,416621,416622,416631,510941,511229,511228 (AFTER COATING),416623,416618,416540,511230,511231,511232,(AFTER COATING), 511234,511235,613881, AND A914477. -PART IDENTIFICATION PER DWGS. 613665,511234,416325,416334,416578,416620, 416622,511229,511228,511230,511231,511232,613881 AND A91477. -MATERIAL AND MAIL CERTIFICATION PER DWGS.613665,323201,A414463,B414463,416325 416334,414451,416543,416574,416578,416620,416621,416622,416631,510941,511229 511228,416623,416618,416540,511230,511231,511232,511234,511235,613881 & A91477 -HYDROSTASTIC TEST IAW NOTE 2 PER DWG 613665 -VERIFY ASSEMBLY IAW ASSEMBLY PROCEDURES NOTES 1,2,3 & 4 PER DWG. 613665 -VERIFY REQUIREMENTS OF NOTE 1 PER DWG. A414463 -VERIFYPLATING PER DWG. A414463 & B4414463 -MAGNETIC PARTICLE INSPECTION PER DWG. A414463,B414463,416622,416623,416540, 511232 AND A91477 -VERIFY REQUIREMENTS OF NOTE 13 PER DWG. A414463 -VERIFY REQUIREMENTS OF NOTE 11 PER DWG. B414463 -VERIFY REQUIREMENTS OF NOTE 18 PER DWG. B414463 -HEAT TREAT PER DWG. 416463,416622 AND 416463 -HARDNESS TEST PER DWG. 416334,416622, AND 416623 -COATING IAW NOTE 4 DWG. 416334,416621 -VERIFY REQUIREMENTS OF NOTE 7 PER DWG. 416543 -COATING IAW NOTE 2 PER DWG. 416620 -COATING IAW NOTE 5 DWG. 416622 -VERIFY THAT THREADS ARE NOT GROUND IAW NOTE 8 PER DWG. 416622 -VERIFY WELDING IAW NOTE 4 PER DWG. 510941.511232 AND 613881 -HEAT TREAT 510941-2 PRIOR TO HEAT TREAT PER DWG. 510941 -HARDNESS TEST 510941-2 PER DWG. 510941 -MAGNETIC PARTICLE INSPECTION 510941-2 PRIOR TO WELDING IAW NOTE 8 PER DWG 510941 -MAGNETIC PARTICLE INSPECTION 510941-1 PRIOR TO AND AFTER (ASTM E1444 PARA 6.1.4.3) PLATING IAW NOTE 8 PERDWG. 510941. 510941 -MAGNETIC PARTICLE INSPECTION 510941-1 PRIOR TO AND AFTER (ASTM E1 E1444 PARA 6.1.4.3) PLATING IAW NOTE 8 PER DWG. 510941 -ASSEMBLE PER DWG. 511229,511234, AND 511235 -COATING IAW NOTE 8 PER DWG. 511228 -PENETRANT INSPECTION PER DWG. 511231 -COATING IAW NOTE 7 PER DWG. 511232 -HYDROSTATIC TEST IAW NOTE 10 PER DWG. 511232 -VERIFY VENDOR SUBSTANTIATION OF REQUIREMENTS OF NOTE 3 IAW NOTE 6 PER DWG. 511234 -VERIFY VENDOR SUBSTANTIATION OF REQUIREMENTS OF NOTE 3 IAW NOTE 7 PER DWG. 511235 -COATING IAW NOTE 6 PER DWG. 613881 -VERIFY REQUIREMENTS OF NOTE 4 PER DWGS A91477 -100% INSPECT AND RECORD THE READINGS FOR THE PITCH DIAMETER;AND DOCUMENT THAT THE INSPECTION RESULTS FOR THE FUNCTION SIZE IAW SYSTEM 22 OF FED-STD-H28/20 ARE ACCEPTABLE PER DWG. 511228,511232,511234,A414463,B414463 -COPIES OF ALL APPROVED DEVIATION AND WAIVERS DATE OF FIRST SUBMISSION=ASREQ block 6: forward additional copy to aso code cited in block 10.A on page 1. WELD PROCEDURE: WELD PROCEDURE IAW NAVSEA S9074-AR GIB-010/278 para 4.2.1 PER DWG. 510941, 511232, & 613881. APPROVAL OR REASON FOR DISAPPROVAL SHALL BE GIVEN BY NAVAIRWARCENACDIVLKE VIA THE PCO NLT 45 DAYS AFTER DISAPPROVAL. NAVAIR CODES: NAVAIRWARCENACDIVLKE CODE BL14000 BLDG 596 HWY 547 LAKEHURST, NJ 08733 NAVAIRWARCENACDIVLKE CODE BL32300 BLGG 562 HWY 547 LAKEHURST, NJ 08733 NAVAIRWARCENACDIVLKE CODE BL41600 BLDG 148 HWY 547 LAKEHURST, NJ 08733 WELDING PROCEDURE QUALIFICATION REPORT THE WELD PROCEDUREM QUALIFICATION TEST REPORT, INCLUDING ALL SUPPORTING DOCUMENTATION, IAW NAVSEA S9074-AQ-GIB-010/248 PARA 4.2.3 AND 4.6 THRU 4,6,1,1 PER DWG.510941,511232 AND 613881. NAVAIR CODES: NAVAIRWARCENACDIVLKE CODE BL14000 BLDG 596 HWY 547 LAKEHURST, NJ 08733 NAVAIRWARCENACDIVLKE CODE BL32300 BLDG 562 HWY 547 LAKEHURST, NJ 08733 NAVAIRWARCENACDIVLKE CODE BL41600 BLDG 148 HWY 547 BLKEHURST, NJ 08733 WELDER PERFORMANCE QUALIFICATION: EVIDENCE OF WELDER PERFORMANCE QUALIFICATIONS, INCLUDING SUPPORTING TESTS RESULTS AND DOCUMENTATION, IAW NAVSEA S9074-AQ-GIB-010/248 PARA 5.2.3 THRU 5.2.3.1 AND 5.2.12 PER DWGS. 510941,511232 & 613881 NAVAIR CODES: NAVAIRWARCENACDIVLKE CODE BL32300 BLDG 562 HWY 547 LAKEHURST, NJ 08733 NAVAIRWARCENACDIVLKE CODE BL41600 BLDG 148 HWY 547 LAKEHURST, NJ 08733 LEVEL III: EVIDENCE OF LEVEL IIII CERITIFICATION IAW T9074-AS-010/271 PARA 1.6 FOR THE INDIVIDUAL WHO APPROVED THE WELDERS QUALIFICATION TRAINING PROGRAM IAW NAVSEA S9074-AQ-GIB-101/248 PARA 5.2.3.1(d) PER DWG. 510941,511232,613881. NAVAIR CODES: NAVAIRWARCENACDIVLKE CODE BL32300 BLDG 562 HWY 547 LAKEHURST, NJ 08733 NAVAIRWARCENACDIVLKE CODE BL41600 BLDG 148 HWY 547 LAKEHURST, NJ 08733 VISUAL INSPECTION WRITTEN PROCEDURE: VISAUL INSPECTION VISUAL INSPECTION WRITTEN PRECEDURE TO BE USED TO VISUALLY INSPECT ALL WELDS IAW T9074-AS-GIB-010/271 PARA 8.3 AND 1.7 THRU 1.7.3 PER DWG. 510941 AND 511232 & 613881 NAVAIR CODES: NAVAIRWARCENACDIVLKE CODE BL32300 BLDG 562 HWY 547 LAKEHURST, NJ 08733 NAVAIRWARCENACDIVLKE CODE BL41600 BLDG 148 HWY 547 LAKEHURST, NJ 08733 DATE OF FIRST SUBMISSION=090 DAC block 6: forward additional copy to aso code cited in block 10.A on page 1. WELDER QUALIFICATION TRAINING WRITTEN PROGRAM: EVIDENCE OF APPROVAL OF THE WELDER QUALIFICATION TRAINING PROGRAM IAW NAVSEA- S9074-AQ-GIB-010/248. NAVAIR CODES: NAVAIRWARCENACDIVLKE CODE 32300 BLDG 562 HWY 547 LAKEHURS...

Inactive

NSN 7R-1720-011424270-EY, TDP VER 021, REF NR 613665-2, QTY 8 EA, DELIVERY FOB ORIGIN. This part requires engineering source approval by the design control activity in order to maintain the quality of... NSN 7R-1720-011424270-EY, TDP VER 021, REF NR 613665-2, QTY 8 EA, DELIVERY FOB ORIGIN. This part requires engineering source approval by the design control activity in order to maintain the quality of the part. Existing unique design capability, engineering skills, and manufacturing/repair knowledge by the qualified source(s) require acquisition/repair of the part from the approved source(s). The approved source(s) retain data rights,manufacturing/repair knowledge, or technical data that are not economically available to the Government, and the data or knowledge is essential to maintaining the quality of the part. An alternate source must qualify in accordance with the design control activity's procedures, as approved by the cognizant Government engineering activity. The qualification procedures must be approved by the Government engineering activity having jurisdiction over the part in the intended application. The subject item requires Government source approval prior to contract award, as the item is flight critical and/or the technical data available has not been determined adequate to support acquisition via full and open competition. Only the source(s) previously approved by the Government for this item have been solicited. The time required for approval of a new source is normally such that an award cannot be delayed pending approval of a new source. If you are not an approved source you must submit, together with your proposal, the information detailed in one of the NAVSUP Weapon Systems Support (NAVSUP WSS)Source Approval Information Brochures listed below. Spares: https://www.navsup.navy.mil/NAVSUP-Enterprise/NAVSUP-Weapon-Systems-Sup port/Business-Opps/ Repair: https://www.navsup.navy.mil/NAVSUP-Enterprise/NAVSUP -Weapon-Systems-Support/Business-Opps/ technical data required to be submitted based on your company's experience in production of the same or similar item, or if this is an item you have never made. If your request for source approval is currently being evaluated at NAVSUP WSS submit with your offer a copy of the cover letter which forwarded your request for source approval. Offers received which fail to provide all data required by the Source Approval Brochure or document previous submission of all data required by the Source Approval Brochure will not be considered for award under this solicitation. Please note, if evaluation of a source approval request submitted hereunder cannot be processed in time and/or approval requirements preclude the ability to obtain subject items in time to meet Government requirements, award of the subject requirement may continue based on Fleet support needs. The NAVSUP WSS Commercial Item Identification Brochure is now available at: "https://www.navsup.navy.mil/NAVSUP-Enterprise/NAVSUP-Weapon-Systems-Support/Bus iness-Opps/"Interested parties may obtain copies of Military and Federal Specificationsand Standards, Qualified Products Lists (QPLs), Qualified Product Databases(QPDs), Military Handbooks, and other standardized documents from the DoDSingle Stock Point (DODSSP) at Document Automation and Production Service(DAPS) in Philadelphia, PA. NOTE: Patterns, Drawings, Deviation Lists, Purchase Descriptions, etc. are NOT stocked at DODSSP. Most documents are available in Adobe PDF format from ASSIST-Online at: http://quicksearch.dla.mil/. Users may use ASSIST-Quick Search to search for and download available documents directly using standard browser software. Documents that are not available for downloading from ASSIST-Quick Search can be ordered from the DODSSP website using the ASSIST Shopping Wizard after obtaining a DODSSP Customer Account by following the registration procedures. Users who do not have access to the internet may contact the DODSSP ASSISTHelp Desk at 215-697-2667 or 215-697-2179 (DSN: 442-2667), or mail their request to DLADocument Services, Bldg. 4/D, 700 Robbins Avenue, Philadelphia PA 19111-5094.The proposed contract action is for supplies or services for which theGovernment intends to solicit and negotiate with only one source under the authority of FAR 6.302-1. All responsible sources may identify their interest and capability to respond to the requirement or submit proposals, quotationsor capability statements. This notice of intent is not a request forcompetitive proposals. However, all proposals received within 45 days (30days if award is issued under an existing Basic Ordering Agreement (BOA) afterdate of publication of this synopsis will be considered by the Government. A determination by the Government not to compete with this proposed contract based upon responses to this notice is solely within the discretion of the Government. Information received will normally be considered solely for the purpose of determining whether to conduct a competitive procurement.Award will be made only if the offeror, the product/service, or themanufacturer meets the qualification requirement(s) at time of award, inaccordance with FAR clause 52.209-1. The solicitation identifies the officewhere additional information can be obtained concerning qualificationrequirements and is cited in each individual solicitation.Based upon market research, the Government is not using the policies containedin FAR Part 12, Acquisition of Commercial Items, in its solicitation for thedescribed supplies or services. However, interested persons may identify tothe contracting officer their interest and capability to satisfy theGovernment's requirement with a commercial item within 15 days of this notice.One or more of the items under this acquisition is subject to: Free Trade Agreements, if DFARS clause 252.225-7036 Buy American Act--Free Trade Agreements--Balance of Payments Program, is included in thesolicitation. The World Trade Organization Government Procurement Agreement and Free Trade Agreements, if DFARS clause 252.225-7021 Trade Agreements, is included in the solicitation. All contractual documents related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile, or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein.