Inactive Total Small Business Set-Aside (FAR 19.5)

NSN 1H-5340-014154667, TDP VER 005, QTY 35 EA, DELIVERY FOB ORIGIN. The Government has rights to the technical data, the data package is complete, and there are no technical data, engineering, tooling... NSN 1H-5340-014154667, TDP VER 005, QTY 35 EA, DELIVERY FOB ORIGIN. The Government has rights to the technical data, the data package is complete, and there are no technical data, engineering, tooling or manufacturing restrictions. (This is the only A/RMSC that implies that parts are candidates for full and open competition. Other A/RMSCs such as K, M, N, Q, and S may imply limited competition when two or more independent sources exist yet the technical data package is inadequate for full and open competition.) A/RMCs 1 or 2 are valid.Interested parties may obtain copies of Military and Federal Specifications and Standards, Qualified Products Lists (QPLs), Qualified Product Databases (QPDs), Military Handbooks, and other standardized documents from the DoD Single Stock Point (DODSSP) at Document Automation and Production Service (DAPS) in Philadelphia, PA. NOTE: Patterns, Drawings, Deviation Lists, Purchase Descriptions, etc. are NOT stocked at DODSSP. Most documents are available in Adobe PDF format from ASSIST-Online at: http://quicksearch.dla.mil/. Users may use ASSIST-Quick Search to search for and download available documents directly using standard browser software. Documents that are not available for downloading from ASSIST-Quick Search can be ordered from the DODSSP website using the ASSIST Shopping Wizard after obtaining a DODSSP Customer Account by following the registration procedures. Users who do not have access to the internet may contact the DODSSP ASSIST Help Desk at 215-697-2667 or 215-697-2179(DSN: 442-2667), or mail their requestDLA Document Services, Bldg. 4/D, 700 Robbins Avenue, Philadelphia PA 19111-5094. Award will be made only if the offeror, the product/service, or the manufacturer meets the qualification requirement(s) at time of award, in accordance with FAR clause 52.209-1. The solicitation identifies the office where additional information can be obtained concerning qualification requirements and is cited in each individual solicitation.Based upon market research, the Government is not using the policies contained in FAR Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice.One or more of the items under this acquisition is subject to: Free Trade Agreements, if DFARS clause 252.225-7036 Buy American Act--Free Trade Agreements--Balance of Payments Program, is included in the solicitation. The World Trade Organization Government Procurement Agreement and Free Trade Agreements, if DFARS clause 252.225-7021 Trade Agreements, is included in the solicitation. Options might be added. This is a procurement, not repair

Inactive

CONTACT INFORMATION|4|N744.13|BLB|n/a|gordon.kohl@navy.mil| ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|||||||||||||||||||| HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (NAVICP REVIEW FEB 1991... CONTACT INFORMATION|4|N744.13|BLB|n/a|gordon.kohl@navy.mil| ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|||||||||||||||||||| HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (NAVICP REVIEW FEB 1991)(FEB 1999)|1|ISO 9001| INSPECTION OF SUPPLIES--FIXED-PRICE (AUG 1996)|2||| NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1|WSS| FIRST ARTICLE APPROVAL--CONTRACTOR TESTING (SEP 1989)|10|one|0001aa|30 days|tbd, based on delivery days on award|will provide upon award|tbd upon award|0001aa|tbd|x| | BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11|||||||||||| NOTICE OF TOTAL SMALL BUSINESS SET-ASIDE (OCT 2020)(DEVIATION 2020-O0008)|1|| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13|||||||||||||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5|||||| BUY AMERICAN-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024)|1|| ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND2025-O0004))|13|332510|750|||||||||||| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PERPARDENESS, AND ENRGY PROGAM USE (APRIL 2008))|2||x| You must provide proof of ISO9001. You must answer the questions that are in the original solicitation notes. Email the POC the answers, as part of your quote. Submit your quote by email to the POC. This is the only acceptable way to submit a quote. Drawing are available in SAM. Request access to them there. Solicitation N0010425QNC75 is for similar items. \ Drawings should post by mid to late May. Solicitation extended, as a result. Request access to them on the Solicitation in Contract Opportunities inSam.gov, when available. The POC does not know when they will be posted , since the POC is not the one who posts them. Keep checking for them.N0010425QNC75 is also in the same situation. If you meet the eligibility and have the ISO quality, both of these solicitations should be considered. There will also be another solicitation for similar plates, about 22 of them or so, that will likely be posted in early June, making 3 Solicitations total for s similar plates. 1. This requirement is pursuant to Emergency Acquisition Flexibilities (EAF). 2. The resultant award of this solicitation will be issued bilaterally, requiring the contractor's written acceptance prior to execution. 3. All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders, and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile, or sent by other electronic commerce methods suchas email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein. 4. This solicitation requires First Article Testing (FAT). See FAR 52.209-3 First Article Approval - Contractor Testing for more details. Questions to answer within your quote, in addition to your price : 1. Delivery Lead Time for first unit: __________________________ 2. If more than one unit to build, after shipping the first unit, the number of assets able to ship each month thereafter ________ 3. Offer valid until ___________________. I prefer that quotes be valid throughat least 30 Sep, if feasible.) 4. Source Inspection Location (CAGE): ________ Note, inspection by DCMA is required prior to shipping. Destination Inspection is not allowed. 5. Source Acceptance Location (CAGE): ________ Inspection by DCMA is required prior to shipping. Destination Acceptance is not allowed. 6. Pack Location (CAGE): ________ Indicate if packaging will be done by an outside source. 7. Is this going to be manufactured in the US? ______ 8. POC name and email: ____________________________ Default clause has been added in case awardee's first article test is rejected as inadequate, or if delinquent in its submission, or never submitted. Item requires ISO 9001 quality. 1. SCOPE 1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the PLATE,MOUNTING . 2. APPLICABLE DOCUMENTS 2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.1.1 Documents, drawings, and publications supplied are listed under "Drawing Number". These items should be retained until an award is made. 2.1.2 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.2 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the text of this contract/purchase order shall take precedence. Nothing in this contract/purchase order, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. DRAWING DATA=497A10012 |53711| E| |D| | | | DRAWING DATA=497A10104 |53711| E| |D| | | | DRAWING DATA=497A63201 |53711| E| |D| | | | DRAWING DATA=497A73200 |53711| G| |D| | | | DRAWING DATA=497A73201 |53711| B| |D| | | | DRAWING DATA=497A80018 |53711| D| |D| | | | DRAWING DATA=497A80072 |53711| B| |D| | | | DRAWING DATA=8482141 |53711| A| |D| | | | DRAWING DATA=8482148 |53711| -| |D| | | | DRAWING DATA=8482149 |53711| A| |D| | | | DRAWING DATA=8482158 |53711| A| |D| | | | DRAWING DATA=8482159 |53711| -| |D| | | | DRAWING DATA=8482160 |53711| -| |D| | | | DRAWING DATA=8482161 |53711| A| |D| | | | DOCUMENT REF DATA=MIL-STD-129 | | |P |041029|A| |03| DOCUMENT REF DATA=MIL-A-24456 | | | |790615|A| 3| | DOCUMENT REF DATA=ASME-Y14.5.1M | | | |941114|A| | | DOCUMENT REF DATA=MIL-DTL-15024 | | |F |971128|A| | | DOCUMENT REF DATA=ASTM-D329 | | | |901026|A| | | DOCUMENT REF DATA=MIL-PRF-81733 | | |D |980515|A| | | DOCUMENT REF DATA=ISO9001 | | | |010417|A| | | DOCUMENT REF DATA=MIL-STD-973 | | | |950113|A| |03| 3. REQUIREMENTS 3.1 Design, Manufacture, and Performance - Except as modified herein, the PLATE,MOUNTING furnished under this contract/purchase order shall meet the design, manufacture, and performance requirements specified on drawing ;497A73200; cage ;53711; . 3.1.1 ;PN - 497A73200-29; 3.2 Marking - This item shall be physically identified in accordance with ;MIL-STD-129; . 3.3 ;The requirements of 53711 drawing #497A73200 are such that a potential vendor must comply with multiple drawing and mil-spec requirements prior to award. The item required is an assembly of parts. The piece parts and the assemblage processes need to comply with all requirements as desribed in the production notes and subsequent drawing specification requirements. The following drawings specifications require process qualification prior to acceptance of production orders: NAVSEA Drawing 8482161, Process Specification for Vulcanization of Chloroprene Rubber (per 3.6) NAVSEA Drawing 8482159, Process Specification for Installation of Vibration Damping Tiles (per 3.6) NAVSEA Drawing 8482158, Process Specification For Bonding with Epoxy Adhesives (per 3.6) NAVSEA Drawing 8482160, Process Specification for Gap Filling (per 3.6) Per NAVSEA DRAWINGS: 3.6 Qualification. This specification requires process qualification prior to acceptance of production orders. The qualification need not be accomplished for repeat orders, provided that the materials and processes have not been changed. With each production order the supplier shall furnish certification in writing that the materials and processes have not been changed in any way from that used when the process was originally qualified. 3.6.1 Requalification. The supplier is advised that if the material formulation or manufacturing process has been changed since the receipt of qualification approval, requalification shall be required before supplying the product manufactured inaccordance with this specification. The supplier shall notify the procuring activity prior to change. The procuring activity will determine the extent of the requalification. 4.2.1 Qualification Test. Process qualification tests are specified in Table 1. Each bonded materials combination for Type I bond shall be tested to qualify the bonded strength and peel rate. ; 3.4 First Article Approval (Contractor Testing) - First Article Test (FAT) and approval is required. 3.4.1 ;First Article Test/Inspection (Contractor) - FIRST ARTICLE INSPECTION: CONDUCT TENSILE TEST ON ALL BONDED STRUCTURE IAW 8482158. BONDED INSERTS SHALL WITHSTAND A MINIMUM 6,000 LBS LOAD WITHOUT BONDAND/OR STRUCTURE DEGRADATION. VERIFY CURED HARDNESS IAW MIL-PRF-81733. ; 3.5 Production Lot Approval (Contractor Testing) - Production Lot Test and approval is required. 3.5.1 ;QUALITY CONFORMANCE TESTS: PERFORM CURED FN 14 HARDNESS TEST IAW MIL-PRF-81733 ON EACH BATCH OF MIXEDMATERIAL USED FOR STRUCTURE BONDING. ; 3.6 Configuration Control - MIL-STD-973 entitled "Configuration Management", Paragraph 5.4.8, Configuration Control (Short Form Procedure), is hereby incorporated. The Contractor shall submit all Engineering Change Proposals in accordance with MIL-STD-973, Paragraph 5.4.8.2 and Appendix D. Requests for Deviations shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.3 and Appendix E. Requests for Waivers shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.4 and Appendix E. (Original and two copies shall be submitted to Contracting Officer, NAVICP-MECH, P. O. Box 2020, Mechanicsburg Pa. 17055-0788.) 3.6.1 Configuration Control - When the Contractor has received authorization on a prior contract for the same NSN for the use of a drawing of a later revision status, that authorization is hereby extended to all succeeding contracts/purchase orders until another drawing revision is approved. The Contractor will notify the PCO of this occurrence in each instance, in the response to the solicitation. Such notification shall be in writing setting forth the contract under which the prior authorization was granted, the date of the granting of the authorization, and the name of the granting authority. Contractors shall also refer technical inquiries (other than those covered by MIL-STD-973) on company letterhead signed by a responsible company official, with copies distributed as stated below. The original and two copies of all Contractor generated correspondence regarding configuration shall be submitted to Contracting Officer, NAVICP-MECH, P.O. Box 2020, Mechanicsburg, PA 17055-0788. Contractors are cautioned that implementing engineering changes, waivers, deviations or technical inquiries into the contract/purchase order without approval of the Contracting Officer will be at the sole risk of the Contractor. 3.7 Mercury Free - The material supplied under this contract/purchase order is intended for use on submarines/surface ships and therefore shall contain no metallic mercury and shall be free from mercury contamination. Mercury contamination of the material will be cause for rejection. If the inclusion of metallic mercury is required as a functional part of the material furnished under this contract, the Contractor shall obtain written approval from the Procurement Contracting Officer before proceeding with manufacture. The contractor's request shall explain in detail the requirements for mercury, identify specifically the parts to contain mercury, and explain the method of protection against mercury escape. Such a request will be forwarded directly to the Procurement Contracting Officer with a copy to the applicable Government Inspector. Upon approval by the Contracting Officer, the vendor will provide a "Warning Plate" stating that metallic mercury is a functional part of the item and will include name and location of that part. The use of mercury, mercury compounds, or mercury-bearing instruments and/or equipment in a manner which might cause contamination in the manufacture, assembly, or test of material on this contract is prohibited. The most probable causes of contamination are direct-connected manometers, mercury vacuum pumps, mercury seals, or the handling of mercury in the immediate vicinity. Mercury switches, mercury in glass thermometers, standard cells and other items containing mercury may be used if they are located so as not to constitute a contamination hazard. If external contamination by metallic mercury occurs or is suspected, the following test may be used to determine whether contamination by metallic mercury exists or whether corrective cleaning measures have been effective. Enclose the equipment in a polyethylene bag or close-fitting airtight container for eight hours at room temperature (70 degrees F minimum).Sample the trapped air and if mercury vapor concentration is 0.01 mg/cu meter or more, the material is mercury contaminated insofar as the requirements of this contract are concerned. These requirements shall be included in any subcontract or purchase order hereunder and the Contractor shall insure SubContractor compliance with these requirements. Technical questions pertaining to these requirements shall be referred to the Procurement Contracting Officer via the cognizant Administrative Contracting Officer. For background, the following information is provided: Mercury is corrosive to gold, silver, nickel, stainless steels, aluminum and copper alloys. Stainless steels, nickel, and copper alloys are widely used in reactor plants and other submarine/surface ship systems. Accidental trapping of mercury in a component could cause serious damage to vital parts. Mercury is also toxic if inhaled, ingested, or absorbed through the skin. It is evident that grave consequences could result from small amounts of mercury vapor present in an unreplenished submarine/surface ship atmosphere. 4. QUALITY ASSURANCE 4.1 Responsibility for Inspection - Unless otherwise specified in the contract/purchase order, the Contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract/purchase order, the Contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Quality System Requirements - The supplier shall provide and maintain a quality system acceptable to the Government. The quality system requirements shall be in accordance with ISO 9001. 4.2.1 ;Suppliers currently using and maintaining Inspection System Requirements to MIL-I-45208 are granted permission to utilize this if desired.; 4.3 Responsibility for Compliance - All items must meet all requirements of this contract/purchase order. The inspection set forth in this specification shall become a part of the Contractor's overall inspection system or quality program. The absence of any inspection requirements shall not relieve the Contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract/purchase order. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, not does it commit the Government to acceptance of defective material. 4.4 Records of Inspection - (This requirement is not applicable to Government Purchase Orders) Records of all inspection work performed by the Contractor, as referenced elsewhere in this contract, shall be kept complete and available to the Government during the performance of the contract and for a period of four years after final delivery of supplies. 4.5 First Article Test/Inspection Report - The Contractor shall prepare and submit a report in accordance with the Contract Data Requirements List (DD Form 1423). The report shall be approved prior to production. 5. PACKAGING 5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below. MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE 6. NOTES 6.1 Ordering Information for Document References - The Department of Defense Single Stock Point (DODSSP), Website http://www.dsp.dla.mil/, provides product information for the Department Of Defense Index Of Specifications and Standards (DODISS) (i.e.Military/Federal Specifications and Standards), Data Item Descriptions (DIDs), and other DODSSP Products. A. Availability of Cancelled Documents - The DODSSP offers cancelled documents that are required by private industry in fulfillment of contractual obligations in paper format. Documents can be requested by phoning the Subscription Services Desk. B. Commercial Specifications, Standards, and Descriptions - These specifications, standards and descriptions are not available from Government sources. They may be obtained from the publishers of the applicable societies. C. Ordnance Standards (OS), Weapons Specifications (WS), and NAVORD OSTD 600 Pages - These type publications may be obtained by submitting a request to: Commander, Indian Head Division, Naval Surface Warfare Center Code 8410P, 101 Strauss Avenue Indian Head, MD 20640-5035 D. On post-award actions, requests for "Official Use Only" and "NOFORN" (Not Releasable To Foreign Nationals) documents must identify the Government Contract Number, and must be submitted via the cognizant Defense Contract Management Command (DCMC) for certification of need for the document. On pre-award actions such requests must be submitted to the PCO for certification of need for the document. E. NOFORN Military Specifications and Standards (including Amendments, Change Notices and Supplements, but NOT interim Changes) to be ordered from: Contracting Officer NAVICP-MECH Code 87321 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788 F. Nuclear Reactor Publications Assigned NAVSEA Documents and Identification Numbers (i.e. NAVSEA Welding Standard, NAVSEA 250-1500-1) are to be ordered from: Commanding Officer NAVICP-MECH Code 009 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788 G. Technical Manuals Assigned NAVSEA Identification Numbers (i.e. NAVSEA Welding And Brazing Procedure, NAVSEA S9074-AQ-GIB-010/248) are to be ordered from: Naval Inventory Control Point Code 1 Support Branch 700 Robbins Avenue Phildelphia, Pa. 19111-5094 H. Interim Changes and Classified Specifications shall be obtained by submitting a request on DD Form 1425 to NAVICP-MECH. DATE OF FIRST SUBMISSION=ASREQ ;APPROVAL OF THE REPORT BY NUWC NWPT ISEA REQUIRED PRIOR TO COMMENCEMENT OF PRODUCTION LOT UNITS.; Michael Reed Naval Undersea Warfare Center Division Newport Code 1533, Hull Arrays and Distributed Sensors michael.d.reed@navy.mil DATE OF FIRST SUBMISSION=ASREQ QUALITY CONFORMANCE TESTS TO BE PERFORMED AS HARDNESS TEST IAW MIL-PRF-81733 ON EACH BATCH OF MIXEDMATERIAL USED FOR STRUCTURE BONDING. POC REGARDING TESTING IS AS FOLLOWS: Michael Reed Naval Undersea Warfare Center Division Newport Code 1533, Hull Arrays and Distributed Sensors michael.d.reed@navy.mil