Inactive Total Small Business Set-Aside (FAR 19.5)

NSN 1H-2040-012846158-SQ, TDP VER 002, QTY 1 EA, DELIVER TO W25G1U, W1A8 DLA DISTRIBUTION, NEW CUMBERLAND, PA 17070-5002. The Government has rights to the technical data, the data package is complete,... NSN 1H-2040-012846158-SQ, TDP VER 002, QTY 1 EA, DELIVER TO W25G1U, W1A8 DLA DISTRIBUTION, NEW CUMBERLAND, PA 17070-5002. The Government has rights to the technical data, the data package is complete, and there are no technical data, engineering, tooling or manufacturing restrictions. (This is the only A/RMSC that implies that parts are candidates for full and open competition. Other A/RMSCs such as K, M, N, Q, and S may imply limited competition when two or more independent sources exist yet the technical data package is inadequate for full and open competition.) A/RMCs 1 or 2 are valid. The proposed acquisition is 100% set aside for small business concerns (see FAR clause 52.219-6, Notice of Total Small Business Set-Aside). The specific type of set-aside will be addressed in the solicitation through inclusion of one of the appropriate clauses listed here: FAR 52.219-3 Notice of HUBZone Set-Aside or Sole Source Award FAR 52.219-27 Notice of Service-Disabled Veteran-Owned Small Business Set-Aside FAR 52.219-29 Notice of Set-Aside for Economically Disadvantaged Women-Owned Small Business Concerns FAR 52.219-30 Notice of Set-Aside for Women-Owned Small Business Concerns Eligible Under the Women-Owned Small Business Program DFARS 252.226-7000 Notice of Historically Black College or University and Minority Institution Set-Aside Based upon market research, the Government is not using the policies contained in FAR Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice. One or more of the items under this acquisition is subject to: Free Trade Agreements, if DFARS clause 252.225-7036 Buy American Act--Free Trade Agreements--Balance of Payments Program, is included in the solicitation. The World Trade Organization Government Procurement Agreement and Free Trade Agreements, if DFARS clause 252.225-7021 Trade Agreements, is included in the solicitation.

Inactive

CONTACT INFORMATION|4|N742.10|ER4|(717) 605-4056|MADISON.M.GRAY4.CIV@US.NAVY.MIL| ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|||||||||||||||||||| HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (... CONTACT INFORMATION|4|N742.10|ER4|(717) 605-4056|MADISON.M.GRAY4.CIV@US.NAVY.MIL| ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|||||||||||||||||||| HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (NAVICP REVIEW FEB 1991)(FEB 1999)|1|See specification sections C and E| INSPECTION OF SUPPLIES--FIXED-PRICE (AUG 1996)|2||| INSPECTION AND ACCEPTANCE - SHORT VERSION|8||||||||| INSPECTION/ACCEPTANCE POINT|6||||||| WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Material-Invoice & Receiving Report (COMBO) |N/A|TBD|N00104|TBD|TBD|W25G1U|TBD|N/A|N/A|N/A|N/A|N/A|N/A|See DD Form 1423|N64498| NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1|| EQUAL OPPORTUNITY (SEP 2016)|2||| WARRANTY OF SUPPLIES OF A NONCOMPLEX NATURE (JUNE 2003)|6|one year from date of delivery|one year from date of delivery||||| WARRANTY OF DATA--BASIC (MAR 2014)|2||| FIRST ARTICLE APPROVAL--CONTRACTOR TESTING (SEP 1989)|10||||||||||| NOTICE OF TOTAL SMALL BUSINESS SET-ASIDE (OCT 2020)(DEVIATION 2020-O0008)|1|| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (NOV 2020)|13|||||||||||||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (DEC 2022))|3|||| BUY AMERICAN-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (NOV 2014)|1|| ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2023)|13|336612|1000 (# of employees)|||||||||||| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PERPARDENESS, AND ENRGY PROGAM USE (APRIL 2008))|2||X| This amendment has been issued to update the TDP from version 002 to version 003. \ The hour and date specified for receipt of offers has been extended to 4:30PM EST on 22 January 2024. \ 1. NAVSUP WSS Mechanicsburg will be considering past performance in the evaluation of offers. See Clause 252.213-7000 and NAVSUP WSS term WSSTERMMZ01. 2. All contractual documents (i.e., contracts, purchase orders, task orders, delivery orders, and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either in the mail, transmitted by facsimile, or sent by other electronic methods, such as email. The Government's acceptance of the contract proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein. 3. The following proposed delivery schedule applies: Non-destructive production lot testing shall be submitted and approved before shipment of PLT units. This solicitation requires First Article Testing. See FAR 52.209-3 First Article Approval - Contractor Testing for more details. Submission of all certification data CDRLs will be on or before 20 days prior to delivery. PNSY review/acceptance of certification CDRLs shall be 6 working days after receipt of certification DD 1423 CDRLs. Final delivery of material shall be on or before 301 days after the effective date of the contract. 4. Any contract/order awarded as a result of this solicitation will be a "DO" rated order certified for national defense use under the Defense Priorities and Allocations System (DPAS). See FAR Clause 52.211-14, Notice of Priority Rating for National Defense, Emergency Preparedness, and Energy Program Use. 5. If drawings are included in the solicitation, access needs to be requested on the individual solicitation page on Contract Opportunities on SAM.gov. After requesting access, send an email to the Primary POC listed on the solicitation. 6. The resultant award of this solicitation will be issued bilaterally, requiring the contractor's written acceptance prior to execution. \ 1. SCOPE 1.1 ;This procurement specification contains the requirements for manufacture and the contract quality requirements for ;OE-592 Antenna Closure Cap Assembly No. 47; for use on Navy submarines.; 2. APPLICABLE DOCUMENTS 2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.1.1 Documents, drawings, and publications supplied are listed under "Drawing Number". These items should be retained until an award is made. 2.1.2 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.1.3 The "Document Changes" section provides supersessions/changes to referenced documents. 2.2 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the text of this contract/purchase order shall take precedence. Nothing in this contract/purchase order, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. DRAWING DATA=4398597 |53711| R| |D|0001 | R|49998|1500835 DRAWING DATA=7325823 |53711| C| |D|0001 | C|49998|0163844 DOCUMENT REF DATA=ASME B1.3 | | | |071012|A| | | DOCUMENT REF DATA=FF-S-86H | | | |210607|A| | | DOCUMENT REF DATA=MIL-STD-973 | | | |000930|A| |04| DOCUMENT REF DATA=MIL-STD-130N | | | |121116|A| |01| DOCUMENT REF DATA=QQ-N-281D | | | |851023|A|2 | | DOCUMENT REF DATA=QQ-N-286G | | | |001207|A| | | DOCUMENT REF DATA=ASME B46.1 | | | | |A| | | DOCUMENT REF DATA=ISO 9001 | | | |150915|A| | | DOCUMENT REF DATA=ISO 10012 | | | |030415|A| | | DOCUMENT REF DATA=NASM15795 | | | |190430|A| | | DOCUMENT REF DATA=NCSL Z540.3 | | | |060803|A| | | DOCUMENT REF DATA=MIL-R-9300B | | | |680115|A| | | DOCUMENT REF DATA=SAE-AMS-QQ-S-763 | | | |150301|A| | | DOCUMENT REF DATA=MIL-P-17549D | | | |810831|A| | | DOCUMENT REF DATA=MIL-DTL-18240F | | | |000313|A|1 | | DOCUMENT REF DATA=FED-STD-H28/20B | | | |940310|A| | | DOCUMENT REF DATA=MIL-I-45208A | | | |951103|A|2 | | DOCUMENT REF DATA=ASTM A240/A240M | | | |001115|A| | | DOCUMENT REF DATA=PHILLYCLAD 1776 RESIN(COML) | | | | |A| | | DOCUMENT REF DATA=PHILLYCLAD 728 HARDENER (COML)| | | | |A| | | DOCUMENT REF DATA=EMERSONFILLER,ECCOFLOATPG30(CO| | | | |A| | | DOCUMENT REF DATA=DOWCORNINGSILICONE RTV-732(COM| | | | |A| | | DOCUMENT CHANGE DATA=MS15795 |NASM15795 DOCUMENT CHANGE DATA=QQ-S-763 |SAE-AMS-QQ-S-763 DOCUMENT CHANGE DATA=QQ-S-766 |ASTM A240/A240M 3. REQUIREMENTS 3.1 ;Design and Manufacturing - The ;OE-592 Antenna Closure Cap Assembly #47; furnished under this contract/purchase order shall meet the material, physical,mechanical and test requirements as specified on Drawings 4398597 (consisting of Item Numbers 7, 9, 10, 18, 22, 25, 26, 27, 30, 36 37, 48, 49, 53, 76 thru 80) and 7325832, Specification MIL-P-17549 including associated specifications mentioned in this procurement. ; 3.1.1 ;The Self-Locking Element Nylok (Configuration Types) furnished under this ordershall be in accordance with MIL-DTL-18240 and shall be products which are qualified on the applicable qualified products list (QPL).; 3.2 ;Marking Requirements - The supplier shall permanently mark and identify each first article and production lot unit ;OE-592 Antenna Closure Cap Assembly #47; Item No. 48 in accordance with Drawing 4398597, Notes 18 and 21 using Item Number 30 (Tag I.D.) as shown on drawing sheet 17 per MIL-STD-130. The supplier shall mark ;tag or bag; each unit with contract per MIL-STD-130.; 3.2.1 ;The supplier shall permanently mark and identify each drawing 4398597, item numbers 22 and 37 as shown on drawing sheet 13 and 37 respectively; and ;tag or bag; each item with contract, drawing/item, heat, lot or batch and serial number per MIL-STD-130 until installed in the designated assembly.; 3.2.2 ;The supplier shall mark ;tag or bag; each drawing 4398597, item number 7, 25, 27, 30, 49, 53, 77 and 78 with contract, drawing/item, heat, lot or batch and serial number per MIL-STD-130 until installed in the designated assembly.; 3.2.3 ;The supplier shall permanently mark and identify each drawing 4398597, item numbers 26 and 76 with the material symbol, manufacture's symbol and lot number on the top face surface per MIL-STD-130; and shall mark ;tag or bag; each item with drawing/ item and contract number per MIL-STD-130 until installed in the designated assembly.; 3.3 ;First Article Testing/Inspection - (Supplier Testing/Inspection). The first article testing/ inspection procedure and approval are required forthe ;OE-592 Antenna Closure Cap Assembly #47;. Government approval is required prior to commencement of first article unit. ; 3.4 ;Notification - The supplier shall notify Naval Surface Warfare Center, Philadelphia Division, (NSWCPD), 5001 S. Broad Street, Philadelphia, PA 19112-1403 by email matthew.ogilvie@navy.mil, Code 242MO after award of contract.; 3.4.1 ;The NSWCPD is the acceptance activity for the Contract Data Requirements List (DD1423) Data Items. NSWCPD WAWF/IRAPT ;Acceptor; DODACC is ;N64498;. ; 3.5 Configuration Control - MIL-STD-973 entitled "Configuration Management", Paragraph 5.4.8, Configuration Control (Short Form Procedure), is hereby incorporated. The Contractor shall submit all Engineering Change Proposals in accordance with MIL-STD-973, Paragraph 5.4.8.2 and Appendix D. Requests for Deviations shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.3 and Appendix E. Requests for Waivers shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.4 and Appendix E. (Original and two copies shall be submitted to Contracting Officer, NAVICP-MECH, P. O. Box 2020, Mechanicsburg Pa. 17055-0788.) 3.5.1 Configuration Control - When the Contractor has received authorization on a prior contract for the same NSN for the use of a drawing of a later revision status, that authorization is hereby extended to all succeeding contracts/purchase orders until another drawing revision is approved. The Contractor will notify the PCO of this occurrence in each instance, in the response to the solicitation. Such notification shall be in writing setting forth the contract under which the prior authorization was granted, the date of the granting of the authorization, and the name of the granting authority. Contractors shall also refer technical inquiries (other than those covered by MIL-STD-973) on company letterhead signed by a responsible company official, with copies distributed as stated below. The original and two copies of all Contractor generated correspondence regarding configuration shall be submitted to Contracting Officer, NAVICP-MECH, P.O. Box 2020, Mechanicsburg, PA 17055-0788. Contractors are cautioned that implementing engineering changes, waivers, deviations or technical inquiries into the contract/purchase order without approval of the Contracting Officer will be at the sole risk of the Contractor. 3.6 Mercury Free - The material supplied under this contract/purchase order is intended for use on submarines/surface ships and therefore shall contain no metallic mercury and shall be free from mercury contamination. Mercury contamination of the material will be cause for rejection. If the inclusion of metallic mercury is required as a functional part of the material furnished under this contract, the Contractor shall obtain written approval from the Procurement Contracting Officer before proceeding with manufacture. The contractor's request shall explain in detail the requirements for mercury, identify specifically the parts to contain mercury, and explain the method of protection against mercury escape. Such a request will be forwarded directly to the Procurement Contracting Officer with a copy to the applicable Government Inspector. Upon approval by the Contracting Officer, the vendor will provide a "Warning Plate" stating that metallic mercury is a functional part of the item and will include name and location of that part. The use of mercury, mercury compounds, or mercury-bearing instruments and/or equipment in a manner which might cause contamination in the manufacture, assembly, or test of material on this contract is prohibited. The most probable causes of contamination are direct-connected manometers, mercury vacuum pumps, mercury seals, or the handling of mercury in the immediate vicinity. Mercury switches, mercury in glass thermometers, standard cells and other items containing mercury may be used if they are located so as not to constitute a contamination hazard. If external contamination by metallic mercury occurs or is suspected, the following test may be used to determine whether contamination by metallic mercury exists or whether corrective cleaning measures have been effective. Enclose the equipment in a polyethylene bag or close-fitting airtight container for eight hours at room temperature (70 degrees F minimum).Sample the trapped air and if mercury vapor concentration is 0.01 mg/cu meter or more, the material is mercury contaminated insofar as the requirements of this contract are concerned. These requirements shall be included in any subcontract or purchase order hereunder and the Contractor shall insure SubContractor compliance with these requirements. Technical questions pertaining to these requirements shall be referred to the Procurement Contracting Officer via the cognizant Administrative Contracting Officer. For background, the following information is provided: Mercury is corrosive to gold, silver, nickel, stainless steels, aluminum and copper alloys. Stainless steels, nickel, and copper alloys are widely used in reactor plants and other submarine/surface ship systems. Accidental trapping of mercury in a component could cause serious damage to vital parts. Mercury is also toxic if inhaled, ingested, or absorbed through the skin. It is evident that grave consequences could result from small amounts of mercury vapor present in an unreplenished submarine/surface ship atmosphere. 4. QUALITY ASSURANCE 4.1 Responsibility for Inspection - Unless otherwise specified in the contract/purchase order, the Contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract/purchase order, the Contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Responsibility for Compliance - All items must meet all requirements of this contract/purchase order. The inspection set forth in this specification shall become a part of the Contractor's overall inspection system or quality program. The absence of any inspection requirements shall not relieve the Contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract/purchase order. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, not does it commit the Government to acceptance of defective material. 4.3 Records - Records of all inspection work by the Contractor shall be kept complete and available to the Government during the performance of contract/purchase order and for a period of 365 calendar days after final delivery of supplies. 4.4 ;Inspection System - The Supplier's Quality Inspection System shall be in accordance with MIL-I-45208 or ISO 9001 and NCSL Z540.3 or ISO 10012. The supplier shall develop and submit their written Quality Inspection and Test Plan as indicated on the Contract Data Requirements List (DD Form 1423). Government approval of the supplier's written Quality Inspection and Test Plan is required by the contract. CDRL: QUALITY INSPECTION & TEST PLAN per MIL-I-45208, NCSL Z540.3 and DI-QCIC-81110; 4.5 ;Surface Roughness - All surface finishes are in RMS measurements. Where the degree of surface roughness is indicated, the surface shall be free from all visible imperfections as defined by Standard ASME B46.1.; 4.6 ;Finished Edges - Finished edges shall be in accordance with the applicable drawing requirements.; 4.7 ;Threads - Threads shall be inspected in accordance with FED-STD-H28/20 System 21 requirements, except for drawing 4398597, Item Nos. 26 and 76 threads shall be inspected to System 22 as required by FF-S-86 (in accordance with ASME B1.3). Thread inspection shall include the measurement and recording of the major diameter for external threads and the minor diameter for internal threads.; 4.8 ;Material Control - The supplier shall have an effective material control system that provides for certified quantitative mill or industrial laboratory reports of chemical and physical analysis by heat, lot or batch for raw material ordered for first article and production units. If the material is subsequently heat-treated a certification of physical analysis, after heat treatment is also required for each heat lot or batch. Also, where the applicable material specification calls out (e.g., corrosion resistance test, macro-etch test) these test results shall also be reported on the applicable mill or industrial laboratory report. (1) The physical analysis shall establish the following properties for metallic part: Mechanical Properties (Tensile Strength, Yield Strength, Elongation) including Susceptibility to Intergranular Cracking (Slow Strain Rate Tensile Test) and Hardness per QQ-N-286. (2) The non-metallic material physical analysis shall be in accordance with MIL-P-17549.; 4.9 ;First Article Testing/Inspection - (Supplier Testing/Inspection). The supplier shall perform first article testing/inspection on ;OE-592 Antenna Closure Cap Assembly #47; in accordance with the applicable drawings, Military Specification MIL-P-17549 and their approved first article procedure.; 4.9.1 ;The first article inspection shall be made by the cognizant DCMA-QAR at the supplier's and/or subcontractor facility. The supplier shall notify NSWCPD, Code 242MO two weeks in advance prior to the scheduled first article testing/inspection, so an NSWCPD representative has the option of being present during the first article testing/inspection.; 4.10 ;First Article Approval for Testing/Inspection Procedure and Acceptance - (Supplier Testing/Inspection). The supplier shall prepare and submit their First Article Testing/ Inspection Procedure ;OE-592 Antenna Closure Cap Assembly #47; in accordance with the requirements of DI-NDTI-80603, applicable drawings and MIL-P-17549 as indicated on the Contract Data Requirements List (DD Form 1423). Government approval of the procedure is required prior to commencement of first article unit. CDRL: FIRST ARTICLE TESTING/INSPECTION PROCEDURE per DI-NDTI-80603A; 4.11 ;First Article Testing/Inspection - The supplier shall perform 100% examination, inspection and testing on the first article ;OE-592 Antenna Closure Cap Assembly #47; unit in accordance with the applicable drawings, MIL-P-17549 and their approved first article procedure. The supplier shall record the actual measurements and results of each examination, inspection and test specified in MIL-P-17549 and their approved first article procedure.; 4.11.1 ;Visual/Dimensional Inspection - The supplier shall visually and physically inspect 100% the first article unit (component parts/assembly) and record the actual measurements of each dimension, feature and threads (including of the major diameter for external threads and the minor diameter for internal threads) identified on the applicable drawings. Threads shall be inspected 100% and results recorded.; 4.12 ;First Article Testing/Inspection Report and Acceptance - (Supplier Testing/Inspection). The supplier shall submit for the first article unit ;OE-592 Antenna Closure Cap Assembly #47; testing/inspection reports in compliance with the requirements of DI-NDTI-80603, applicable drawings and MIL-P-17549. The report shall also include a copy of ;Certified Mill Certificate; Certificate of Conformance for Material; Certificate of Compliance for Material and Visual/Dimensional Inspection Report; identified in the Objective Quality Evidence Records Section of this document, and as indicated on the Contract Data Requirements List (DD Form 1423). Government approval of the first article testing/ inspection report is required prior to commencement of production units. CDRL: FIRST ARTICLE TESTING/INSPECTION REPORT per DI-NDTI-80809B; 4.13 ;Production Lot. The supplier shall perform 100% inspection, examination and testing on each completed production unit in accordance with the applicable drawings and requirements listed in MIL-P-17549 (Quality Conformance Inspection). The supplier shall record the actual measurements and results of each examination, inspection and test specified in MIL-P-17549.; 4.13.1 ;Visual/Dimensional Inspection - The supplier shall visually and physically inspect 100% on each (component parts/assemblies) and record the actual measurements of each dimension, feature and threads (including of the major diameter for external threads and the minor diameter for internal threads) identified on the applicable drawing. Threads shall be inspected 100% and results recorded.; 4.14 ;Production Lot Testing/Inspection Report and Acceptance - (Supplier Testing/ Inspection). The supplier shall submit for the completed production units ;OE-592 Antenna Closure Cap Assembly #47; testing/inspection reports in compliance with the applicable Data Item Descriptions (DIDs), drawings and specifications. The Production Lot Testing/ Inspection report shall consist of ;Certified Mill Certification; Certificate of Conformance for Material; Certificate of Compliance for Material; Certified Examination Inspection & Test Report; Visual/Dimensional Inspection Report and Mercury Exclusion Certification; as identified in the Objective Quality Evidence Records Section of this document, and as indicated on the Production Lot Test/Inspection (PLT) Contract Data Requirements List (DD Form 1423). Government approval of the production lot testing/inspection report is required prior to shipment of production lot units. CDRL: PRODUCTION LOT TESTING/INSPECTION REPORT per DI-NDTI- 80809B; 4.15 ;Production Lot Inspection/Acceptance - (Supplier Testing/Inspection). The supplier shall submit for the production lot units, the inspection and test reports identified in the Objective Quality Evidence Records Section of this document and as indicated on the Production Lot Testing/Inspection (PLT) Contract Data Requirements List (DD Form 1423). Government approval is required prior to shipment of production units. ; 4.16 ;Final Inspection and Acceptance - Final inspection and acceptance of production lots shall be made by the cognizant DCMA-QAR. NSWCPD shall either issue Specific Government Inspection Instructions or Inspection Hold Points based on whether DCMA or NSWCPD will be performing the required Inspections/Tests. In addition to the normal DCMA surveillance, the production unit(s) shall be under the surveillance of NSWCPD Quality Assurance Specialist as required.; 4.17 ;Objective Quality Evidence Records - The supplier shall maintain Objective Quality Evidence Data (OQEDs) of raw material and finished parts used in the fabrication of ;OE-592 Antenna Closure Cap Assembly #47;. Records shall be traceable by drawing/item, lot or batch, serial and contract number. All OQEDS shall be clearly legible including name and title. The supplier may provide exact (quality) photocopies of objective quality evidence records being delivered under this purchase order instead of originals.; 4.17.1 ;The supplier shall furnish a copy of the following OQEDs listed below and as indicated on the Contract Data Requirements List (DD Form 1423) for acceptance. The reports shall be correlated to the drawing/item, lot or batch, serial and contract number. Supplier format is acceptable for the below listed CDRLs. a. Certified Quantitative Mill or Industrial Laboratory Certification (chemical and physical analysis) for Item Numbers 7, 25, 26, 30, 53 and 76 of drawing 4398597 including susceptibility to intergranular cracking-slow strain rate tensile test and hardness per QQ-N-286G or later for Item Nos. 26 and 53. CDRL: CERTIFIED MILL CERTIFICATE per DI-MISC-80678 b. Certificate of Conformance for Materials: (1) Item Nos. 22, 48 and 49 (certifying the applicable materials in accordance with drawing 4398597 and MIL-P-17549 requirements). (2) Item Nos. 26 and 76 (certifying Self-Locking Element Nylok Configuration Types in accordance with drawing 4398597 and MIL-DTL-18240 requirements). (3) Item No. 27 (certifying the applicable material in accordance with drawing 4398597 and NASM15795-817 requirements). CDRL: CERTIFICATE OF COMPLIANCE per DI-MISC-80678 d. Certified Examination, Inspection & Test Report shall be in accordance with MIL-P-17549 (Quality Conformance Inspection Requirements) of drawing 4398597, item numbers 22, 48 and 49. CDRL: CERTIFIED EXAMINATION, INSPECTION & TEST REPORT per DI-NDTI-80809B e. Visual/Dimensional Inspection Reports shall show all the characteristics, the actual measurement results of each dimension and feature inspected (component parts/ assemblies) including threads (also the major diameter for external threads and the minor diameter for internal threads), contract number, name of supplier, drawing/item number, drawing revision letter, heat, lot or batch (material symbol and manufacture's symbol for dwg. 4398597, Items 26 and 76) serial and assembly serial number of finished parts, item nomenclature, inspector's acceptance signature and date. CDRL: VISUAL/DIMENSIONAL INSPECTION REPORT per DI-NDTI-80809B f. Mercury Exclusion Certification (representing the contract units shipment) CDRL: MERCURY EXCLUSION CERTIFICATION per DI-MISC-80678; 5. PACKAGING 5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below. MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE 6. NOTES 6.1 Ordering Information for Document References - The Department of Defense Single Stock Point (DODSSP), Website http://www.dsp.dla.mil/, provides product information for the Department Of Defense Index Of Specifications and Standards (DODISS) (i.e.Military/Federal Specifications and Standards), Data Item Descriptions (DIDs), and other DODSSP Products. A. Availability of Cancelled Documents - The DODSSP offers cancelled documents that are required by private industry in fulfillment of contractual obligations in paper format. Documents can be requested by phoning the Subscription Services Desk. B. Commercial Specifications, Standards, and Descriptions - These specifications, standards and descriptions are not available from Government sources. They may be obtained from the publishers of the applicable societies. C. Ordnance Standards (OS), Weapons Specifications (WS), and NAVORD OSTD 600 Pages - These type publications may be obtained by submitting a request to: Commander, Indian Head Division, Naval Surface Warfare Center Code 8410P, 101 Strauss Avenue Indian Head, MD 20640-5035 D. On post-award actions, requests for "Official Use Only" and "NOFORN" (Not Releasable To Foreign Nationals) documents must identify the Government Contract Number, and must be submitted via the cognizant Defense Contract Management Command (DCMC) for certification of need for the document. On pre-award actions such requests must be submitted to the PCO for certification of need for the document. E. NOFORN Military Specifications and Standards (including Amendments, Change Notices and Supplements, but NOT interim Changes) to be ordered from: Contracting Officer NAVICP-MECH Code 87321 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788 F. Nuclear Reactor Publications Assigned NAVSEA Documents and Identification Numbers (i.e. NAVSEA Welding Standard, NAVSEA 250-1500-1) are to be ordered from: Commanding Officer NAVICP-MECH Code 009 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788 G. Technical Manuals Assigned NAVSEA Identification Numbers (i.e. NAVSEA Welding And Brazing Procedure, NAVSEA S9074-AQ-GIB-010/248) are to be ordered from: Naval Inventory Control Point Code 1 Support Branch 700 Robbins Avenue Phildelphia, Pa. 19111-5094 H. Interim Changes and Classified Specifications shall be obtained by submitting a request on DD Form 1425 to NAVICP-MECH. PN: 4398597-E-47 DATE OF FIRST SUBMISSION=ASREQ ;APPROVAL OF THE QUALITY INSPECTION PLAN BY NSWC PHILADELPHIADIVISION IS REQUIRED PRIOR TO FIRST ARTICLE.; ;NSWCPD IS THE ACCEPTANCE ACTIVITY FOR CDRL DATA ITEM A001.NSWCPD WAWF/IRAPT ACCEPTOR DODACC IS "N64498".; DATE OF FIRST SUBMISSION=ASREQ ;PROCEDURE SHALL BE IN ACCORDANCE WITH DRAWING 4398597 ANDMILITARY SPECIFICATION MIL-P-17549 REQUIREMENTS.; ;APPROVAL OF THE PROCEDURE BY NSWC PHILADELPHIA DIVISION ISREQUIRED PRIOR TO COMMENCEMENT OF FIRST ARTICLE UNIT.; ;NSWCPD IS THE ACCEPTANCE ACTIVITY FOR CDRL DATA ITEM A002.NSWCPD WAWF/IRAPT ACCEPTOR DODACC IS "N64498".; DATE OF FIRST SUBMISSION=ASREQ ;APPROVAL OF THE REPORT BY NSWC PHILADELPHIA DIVISION ISREQUIRED PRIOR TO COMMENCEMENT OF PRODUCTION LOT UNITS.; ;NSWCPD IS THE ACCEPTANCE ACTIVITY FOR CDRL DATA ITEM A003.NSWCPD WAWF/IRAPT ACCEPTOR DODACC IS "N64498".; DATE OF FIRST SUBMISSION=ASREQ ;SUPPLIER FORMAT IS ACCEPTABLE.; ;PLT REPORT SHALL CONSIST OF THE OQED RECORDS LISTED IN CONTRACTSECTION E: CERTIFIED MILL CERTIFICATION; CERTIFICATE OFCONFORMANCE MATERIAL; CERTIFICATE OF COMPLIANCE MATERIAL;CERTIFIED EXAMINATION INSPECTION & TEST REPORT; VISUAL/ DIMENSIONAL INSPECTION REPORT AND MERCURY EXCLUSIONCERTIFICATION.; ;APPROVAL OF THE REPORT BY NSWC PHILADELPHIA DIVISION ISREQUIRED PRIOR TO SHIPMENT OF PRODUCTION LOT UNITS.; ;NSWCPD IS THE ACCEPTANCE ACTIVITY FOR CDRL DATA ITEM A004.NSWCPD WAWF/IRAPT ACCEPTOR DODACC IS "N64498".;