Inactive

NSN 7H-4810-014064382, TDP VER 010, QTY 5 EA, DELIVER TO W25G1U, W1A8 DLA DISTRIBUTION, NEW CUMBERLAND, PA 17070-5002, INDUCTION NIIN IS 7H, 4810, 014064382, VALVE, GLOBE, 803-6397408-ASSY97, DELIVER ... NSN 7H-4810-014064382, TDP VER 010, QTY 5 EA, DELIVER TO W25G1U, W1A8 DLA DISTRIBUTION, NEW CUMBERLAND, PA 17070-5002, INDUCTION NIIN IS 7H, 4810, 014064382, VALVE, GLOBE, 803-6397408-ASSY97, DELIVER TO W62G2T, W1A8 DLA DIST SAN JOAQUIN, TRACY, CA 95304-5000, INDUCTION NIIN IS 7H, 4810, 014064382, VALVE, GLOBE, 803-6397408-ASSY97. The Government has rights to the technical data, the data package is complete, and there are no technical data, engineering, tooling or manufacturing restrictions. (This is the only A/RMSC that implies that parts are candidates for full and open competition. Other A/RMSCs such as K, M, N, Q, and S may imply limited competition when two or more independent sources exist yet the technical data package is inadequate for full and open competition.) A/RMCs 1 or 2 are valid. Interested parties may obtain copies of Military and Federal Specifications and Standards, Qualified Products Lists (QPLs), Qualified Product Databases (QPDs), Military Handbooks, and other standardized documents from the DoD Single Stock Point (DODSSP) at Document Automation and Production Service (DAPS) in Philadelphia, PA. NOTE: Patterns, Drawings, Deviation Lists, Purchase Descriptions, etc. are NOT stocked at DODSSP. Most documents are available in Adobe PDF format from ASSIST-Online at: http://quicksearch.dla.mil/. Users may use ASSIST-Quick Search to search for and download available documents directly using standard browser software. Documents that are not available for downloading from ASSIST-Quick Search can be ordered from the DODSSP website using the ASSIST Shopping Wizard after obtaining a DODSSP Customer Account by following the registration procedures. Users who do not have access to the internet may contact the DODSSP ASSIST Help Desk at 215-697-6396 (DSN: 442-6396), or mail their request to DLA Document Services, Bldg. 4/D, 700 Robbins Avenue, Philadelphia PA 19111-5094. Award will be made only if the offeror, the product/service, or the manufacturer meets the qualification requirement(s) at time of award, in accordance with FAR clause 52.209-1. The solicitation identifies the office where additional information can be obtained concerning qualification requirements and is cited in each individual solicitation. Based upon market research, the Government is not using the policies contained in FAR Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice.

Inactive

CONTACT INFORMATION|4|N771.17|GHC|717-605-2727|marsha.williams@navy.mil| ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR 2016)|19|||||||||||||||||||| INSPECTION OF SUPPLIES--FIXED-PRICE (AUG 1996)|2||| ... CONTACT INFORMATION|4|N771.17|GHC|717-605-2727|marsha.williams@navy.mil| ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR 2016)|19|||||||||||||||||||| INSPECTION OF SUPPLIES--FIXED-PRICE (AUG 1996)|2||| GENERAL INFORMATION-FOB-DESTINATION|1|B| WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (DEC 2018)|16|Invoice and receiving report (Combo)|n/a|TBD|N00104|TBD|TBD|See Schedule|TBD|||TBD|||||| NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|2|WSS|WSS| BUY AMERICAN --FREE TRADE AGREEMENTS--BALANCE OF PAYMENTS PROGRAM - BASIC(DEC 2017))|5|||||| OPTION FOR INCREASED QUANTITY (MAR 1989)|1|365 days after date of award| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (JUN 2019)|11|||||||||||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS CERTIFICATE (NOV 2014)|5|||||| BUY AMERICAN-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (NOV 2014)|1|| ANNUAL REPRESENTATIONS AND CERTIFICATIONS (DEC 2019)|12|332911|750||||||||||| REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCESERVICES OR EQUIPMENT (AUG 2019))|2||| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PERPARDENESS, AND ENRGY PROGAM USE (APRIL 2008))|2||x| Estimated repair pricing for tear-down and evaluation only will not be accepted. Please provide either a firm fixed, or a Not-to-exceed repair price, subject todownward negotiation only, and repair turnaround time for the item(s) listed on the schedule page. Verify nomenclature, part number, and NSN prior to responding. Please also provide the estimated cost of a new unit. Government source inspection is required. Please note freight is FOB Origin. All transportation is handled by the U.S. Navy via CAV or Proxy CAV. The contracting officer reserves the right to exercise the option quantity under the option subclin within 365-days of the effective date of this repair of contract award. The contractor will provide the same delivery time and price listed in the schedule. A modification will be completed at the time the option is exercised and all current contract terms and conditions will apply to the option quantity. \ 1. SCOPE 1.1 This contract/purchase order contains the requirements for repair and the contract quality requirements for the VALVE, GLOBE . 2. APPLICABLE DOCUMENTS 2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.1.2 The "Document Changes" section provides supersessions/changes to referenced documents. 2.2 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the text of this contract/purchase order shall take precedence. Nothing in this contract/purchase order, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. DRAWING DATA=6397408 |53711| C| |A|0001 | C|49998|0111026 DRAWING DATA=6397408 |53711| C| |A|0002 | C|49998|0118636 DRAWING DATA=6397408 |53711| C| |A|0003 | C|49998|0142391 DRAWING DATA=6397408 |53711| C| |A|0004 | C|49998|0208918 DRAWING DATA=6397408 |53711| C| |A|0005 | C|49998|0241375 DRAWING DATA=6397408 |53711| C| |A|0005.A | C|49998|0050515 DRAWING DATA=6397408 |53711| C| |A|0006 | C|49998|0067907 DRAWING DATA=6397408 |53711| C| |A|0007 | C|49998|0067608 DRAWING DATA=6397408 |53711| C| |A|0008 | C|49998|0067863 DRAWING DATA=6397408 |53711| C| |A|0009 | C|49998|0069222 DRAWING DATA=6397408 |53711| C| |A|0010 | C|49998|0074289 DRAWING DATA=6397408 |53711| C| |A|0011 | C|49998|0065239 DRAWING DATA=6397408 |53711| C| |A|0012 | C|49998|0069859 DRAWING DATA=6397408 |53711| C| |A|0013 | C|49998|0073427 DRAWING DATA=6397408 |53711| C| |A|0014 | C|49998|0091929 DRAWING DATA=6397408 |53711| C| |A|0015 | C|49998|0105563 DRAWING DATA=6397408 |53711| C| |A|0016 | C|49998|0099773 DRAWING DATA=6397408 |53711| C| |A|0017 | C|49998|0110220 DRAWING DATA=6397408 |53711| C| |A|0018 | C|49998|0071921 DRAWING DATA=6397408 |53711| C| |A|0019 | C|49998|0060319 DRAWING DATA=6397408 |53711| C| |A|0020 | C|49998|0072085 DRAWING DATA=6397408 |53711| C| |A|0021 | C|49998|0051612 DRAWING DATA=6397408 |53711| C| |A|0022 | C|49998|0081751 DRAWING DATA=6397408 |53711| C| |A|0023 | C|49998|0052349 DRAWING DATA=6397408 |53711| C| |A|0024 | C|49998|0081047 DRAWING DATA=6397408 |53711| C| |A|0025 | C|49998|0053254 DRAWING DATA=6397408 |53711| C| |A|0026 | C|49998|0082632 DRAWING DATA=6397408 |53711| C| |A|0027 | C|49998|0054641 DRAWING DATA=6397408 |53711| C| |A|0028 | C|49998|0070455 DRAWING DATA=6397408 |53711| C| |A|0029 | C|49998|0049806 DRAWING DATA=6397408 |53711| C| |A|0030 | C|49998|0071412 DRAWING DATA=6397408 |53711| C| |A|0031 | C|49998|0050521 DRAWING DATA=6397408 |53711| C| |A|0032 | C|49998|0076499 DRAWING DATA=6397408 |53711| C| |A|0033 | C|49998|0052954 DRAWING DATA=6397408 |53711| C| |A|0034 | C|49998|0123838 DRAWING DATA=6397408 |53711| C| |A|0035 | C|49998|0133851 DRAWING DATA=6397408 |53711| C| |A|0036 | C|49998|0138006 DRAWING DATA=6397408 |53711| C| |A|0037 | C|49998|0124220 DRAWING DATA=6397408 |53711| C| |A|0038 | C|49998|0087064 DRAWING DATA=6397408 |53711| C| |A|0039 | C|49998|0105463 DRAWING DATA=6397408 |53711| C| |A|0040 | C|49998|0092263 DRAWING DATA=6397408 |53711| C| |A|0041 | C|49998|0098859 DRAWING DATA=6397408 |53711| C| |A|0042 | C|49998|0110718 DRAWING DATA=6397408 |53711| C| |A|0043 | C|49998|0060485 DRAWING DATA=6397408 |53711| C| |A|0044 | C|49998|0093955 DRAWING DATA=6397408 |53711| C| |A|0045 | C|49998|0061510 DRAWING DATA=6397408 |53711| C| |A|0046 | C|49998|0111652 DRAWING DATA=6397408 |53711| C| |A|0047 | C|49998|0107134 DRAWING DATA=6397408 |53711| C| |A|0048 | C|49998|0079527 DRAWING DATA=6397408 |53711| C| |A|0049 | C|49998|0104723 DRAWING DATA=6397408 |53711| C| |A|0050 | C|49998|0073178 DRAWING DATA=6397408 |53711| C| |A|0051 | C|49998|0050581 DRAWING DATA=6397408 |53711| C| |A|0051.A | C|49998|0042631 DRAWING DATA=6397408 |53711| C| |A|0052 | C|49998|0192884 DRAWING DATA=6397408 |53711| C| |A|0053 | C|49998|0217044 DRAWING DATA=6397408 |53711| C| |A|0054 | C|49998|0198162 DRAWING DATA=6397408 |53711| C| |A|0055 | C|49998|0221571 DRAWING DATA=6397408 |53711| C| |A|0056 | C|49998|0114011 DOCUMENT REF DATA=MIL-STD-129 | | |R |180524|A| |03| DOCUMENT REF DATA=MIL-STD-789 | | |C |080630|A| | | DOCUMENT REF DATA=MIL-A-8625 | | |F |190828|A| | | DOCUMENT REF DATA=MIL-C-15726 | | |F |911008|A| 1| | DOCUMENT REF DATA=MIL-B-24480 | | |A |910326|A| | | DOCUMENT REF DATA=MIL-S-46163 | | |C |100504|A| 2| | DOCUMENT REF DATA=QPL-81733 | | |10 |040423|A| 1| | DOCUMENT REF DATA=MIL-R-83248 | | |C |010621|A| | | DOCUMENT REF DATA=MIL-STD-100 | | |G |011214|A| |01| DOCUMENT REF DATA=ASTM-B150 | | | |050916|A| | | DOCUMENT REF DATA=ASTM-D2000 | | | |910225|A| | | DOCUMENT REF DATA=MIL-PRF-20042 | | |E |990916|A| | | DOCUMENT REF DATA=ASTM-B209M | | | |931115|A| | |N DOCUMENT REF DATA=ASTM-A231/A231M | | | |941003|A| | | DOCUMENT REF DATA=ASTM-B26/B26M | | | |920515|A| | | DOCUMENT REF DATA=ASTM-A276 | | | |940315|A| | | DOCUMENT REF DATA=ASTM-B36/B36M | | | |910222|A| | | DOCUMENT REF DATA=ASTM-B446 | | | |941003|A| | | DOCUMENT REF DATA=ASTM-A479/A479M | | | |940115|A| | | DOCUMENT REF DATA=ASTM-D523 | | | |890331|A| | | DOCUMENT REF DATA=ASTM-B61 | | | |930215|A| | | DOCUMENT REF DATA=MIL-PRF-81733 | | |D |980515|A| | | DOCUMENT REF DATA=MIL-STD-973 | | |C |091005|A| | | DOCUMENT CHANGE DATA=MIL-F-20042 |MIL-PRF-20042 DOCUMENT CHANGE DATA=QQ-A-601 |ASTM-B26 3. REQUIREMENTS 3.1 ;The valve assembly shall be repaired/refurbished in accordance with Naval Sea Systems Command drawing 803-6397408. Assembly part number 803-6397408 Assy 97 applies. One manual operator wrench, test fitting, one 3/8 inch union nut (PC199), female tailpiece (PC 200), and O-Ring shall be supplied with each valve assembly.; 3.1.1 ;Each Valve Assembly shall be completely disassembled, cleaned, and visuallyand dimensionally examined for evidence of wear or damage. All defective parts shall be repaired or replaced. 100% replacement of the following partsare required: Seat, Disk, Disk Gasket, Diaphragm, and O-Ring seals. The valve shall be assembled and tested as specified elsewhere in the purchase order/contract.; 3.2 Marking - This item shall be physically identified in accordance with ;General Note 7 of Drawing 803-6397408; . 3.3 Production Lot Approval (Contractor Testing) - Production Lot Test and approval is required. 3.3.1 Configuration Control - When the Contractor has received authorization on a prior contract for the same NSN for the use of a drawing of a later revision status, that authorization is hereby extended to all succeeding contracts/purchase orders until another drawing revision is approved. The Contractor will notify the PCO of this occurrence in each instance, in the response to the solicitation. Such notification shall be in writing setting forth the contract under which the prior authorization was granted, the date of the granting of the authorization, and the name of the granting authority. Contractors shall also refer technical inquiries (other than those covered by MIL-STD-973) on company letterhead signed by a responsible company official, with copies distributed as stated below. The original and two copies of all Contractor generated correspondence regarding configuration shall be submitted to Contracting Officer, NAVICP-MECH, P.O. Box 2020, Mechanicsburg, PA 17055-0788. Contractors are cautioned that implementing engineering changes, waivers, deviations or technical inquiries into the contract/purchase order without approval of the Contracting Officer will be at the sole risk of the Contractor. 3.4 Configuration Control in accordance with MIL-STD-973 Short Form procedures - The requirements of MIL-STD-973 are hereby invoked in the contract/purchase order. The tailoring notes stated in the order cited in paragraph 6.2.1.3 are stated below: A. Considered, tailoring implemented B. Automated processing and submittal is not required. Interactive access to digital data is not required. C. Configuration audits are not required. D. Contractor's configuration management plan is not requried. E. Configuration terminology development documentation is required. F. Only paragraphs 5.3.3.2, 5.3.6.4, 5.3.6.7, 5.3.6.7.3 are required. G. FCD is not required. H. ACD and PCD is not required. I. Not Applicable (NA) to this contract/purchase order. J. NA to this contract/purchase order. K. NA to this contract/purchase order. L. Paragraph 5.3.6 with the exception of paragraph 5.3.6.5 and 5.3.6.7.1 are required. M. Paragraph 5.3.6.6 and 5.3.6.6.2 are required. N. Paragraph 5.3.6.6.1 is not required unless specifically cited elsewhere in Section "C" of this contract/purchase order. O. The marking requirement is stated elsewhere in Section "C" of this contract/purchase order. P. Interface requirements are as specified on the drawings provided with this contract/purchase order or the primary equipment performance MIL-SPEC or STD cited in Section "C" of this contract/purchase order. Q. NA to this contract/purchase order. R. All Class I changes to either a Government owned Configuration Identification (CI) or baseline configuration shall be submitted to the Procurement Contracting Officer for review and subsequent approval - conditional approval or disapproval. NDI, COTS, and PDI items previously accepted by the Government shall be submitted as above. This process does not excuse the contractor from initially offering to the Government an item which meets the minimum technical and operational requirements set forth in this contract/ purchase order. S. Preliminary Change Notices and Advance Change Study Notices are not required. T. NA to this contract/purchase order. U. and V. Class II Engineering Change Proposal (ECP) may be carried through provided the Government QAR reviews and concurs with the classification review which resulted in the ECP being classified as Class II. W. Paragraph 5.4.3 is required. X. Paragraph 5.4.4 is required. Y. NORS are not required for this contract/purchase order. Z. Short Form procedures are allowed. AA. Paragraph 5.5.2 is not required for this contract/purchase order. AB. Paragraph 5.5.7 is not required for this contract/purchase order. AC. Paragraph 5.5.8 is not required for this contract/purchase order. AD. Paragraph 5.6.2 is not required for this contract/purchase order. AE. Paragarph 5.6.3 is not required for this contract/purchase order. AF. Paragraph 5.4.2.2.3.2b is not required for this contract/purchase order. 3.5 Mercury Free - The material supplied under this contract/purchase order is intended for use on submarines/surface ships and therefore shall contain no metallic mercury and shall be free from mercury contamination. Mercury contamination of the material will be cause for rejection. If the inclusion of metallic mercury is required as a functional part of the material furnished under this contract, the Contractor shall obtain written approval from the Procurement Contracting Officer before proceeding with manufacture. The contractor's request shall explain in detail the requirements for mercury, identify specifically the parts to contain mercury, and explain the method of protection against mercury escape. Such a request will be forwarded directly to the Procurement Contracting Officer with a copy to the applicable Government Inspector. Upon approval by the Contracting Officer, the vendor will provide a "Warning Plate" stating that metallic mercury is a functional part of the item and will include name and location of that part. The use of mercury, mercury compounds, or mercury-bearing instruments and/or equipment in a manner which might cause contamination in the manufacture, assembly, or test of material on this contract is prohibited. The most probable causes of contamination are direct-connected manometers, mercury vacuum pumps, mercury seals, or the handling of mercury in the immediate vicinity. Mercury switches, mercury in glass thermometers, standard cells and other items containing mercury may be used if they are located so as not to constitute a contamination hazard. If external contamination by metallic mercury occurs or is suspected, the following test may be used to determine whether contamination by metallic mercury exists or whether corrective cleaning measures have been effective. Enclose the equipment in a polyethylene bag or close-fitting airtight container for eight hours at room temperature (70 degrees F minimum).Sample the trapped air and if mercury vapor concentration is 0.01 mg/cu meter or more, the material is mercury contaminated insofar as the requirements of this contract are concerned. These requirements shall be included in any subcontract or purchase order hereunder and the Contractor shall insure SubContractor compliance with these requirements. Technical questions pertaining to these requirements shall be referred to the Procurement Contracting Officer via the cognizant Administrative Contracting Officer. For background, the following information is provided: Mercury is corrosive to gold, silver, nickel, stainless steels, aluminum and copper alloys. Stainless steels, nickel, and copper alloys are widely used in reactor plants and other submarine/surface ship systems. Accidental trapping of mercury in a component could cause serious damage to vital parts. Mercury is also toxic if inhaled, ingested, or absorbed through the skin. It is evident that grave consequences could result from small amounts of mercury vapor present in an unreplenished submarine/surface ship atmosphere. 3.6 Qualification Requirements - This item contains components that must be manufactured by a Government Qualified Products List (QPL) supplier. 4. QUALITY ASSURANCE 4.1 Responsibility for Inspection - Unless otherwise specified in the contract/purchase order, the Contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract/purchase order, the Contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Records - Records of all inspection work by the Contractor shall be kept complete and available to the Government during the performance of contract/purchase order and for a period of 365 calendar days after final delivery of supplies. 4.3 Responsibility for Compliance - All items must meet all requirements of this contract/purchase order. The inspection set forth in this specification shall become a part of the Contractor's overall inspection system or quality program. The absence of any inspection requirements shall not relieve the Contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract/purchase order. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, not does it commit the Government to acceptance of defective material. 4.4 Visual, Dimensional, Mechanical Examination - Each VALVE, GLOBE shall be 100% inspected in accordance with ;Drawing 803-6397408; . 4.5 Production Lot Test/Inspection Report - The Contractor shall prepare and submit a report in accordance with the Contract Data Requirements List (DD Form 1423). 4.6 Production Lot Test (Contractor) - The Contractor shall perform 100% production testing in accordance with ;General Notes 6.A thru 6.C of Drawing 803-6397408; . 4.7 Inspection System Requirements - The supplier shall provide and maintain an inspection/quality system acceptable to the Government. The inspection system requirements for this contract/purchase order shall be in accordance with MIL-I-45208. Suppliers certified to perform under ISO 9001 or ISO 9002 are granted permission to utilize the one desired in lieu of MIL-I-45208. Each lot of Diaphragm Material shall be tested in accordance with General Notes 6.D of drawing 803-6397408. Certification of tests are required. 5. PACKAGING 5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below. MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE 6. NOTES 6.1 In accordance with OPNAVINST 5510.1 all documents and drawings provided by the U.S. Navy to perspective Contractors must include a "Distribution Statement" to inform the contractor of the limits of distribution, and the safeguarding of the information contained on those documents and drawings. There are 7 (seven) seperate distribution statement codes used for non-classified documents and drawings. The definition for each is as follows: A... approved for public release; distribution is unlimited. B... distribution authorized to US Governments agencies only. C... distribution authorized to US Government agencies and their contractors. D... distribution authorized to DoD and DoD contractors only. E... distribution authorized to DoD Components only. F... further distribution only as directed by Commander, Naval Sea Systems Command, code 09T. X... distribution is authorized to US Government agencies and private individuals or enterprises eligible to obtain export controlled technical data in accordance with OPNAVINST 5510.161. 6.2 Ordering Information for Document References - The Department of Defense Single Stock Point (DODSSP), Website http://www.dsp.dla.mil/, provides product information for the Department Of Defense Index Of Specifications and Standards (DODISS) (i.e.Military/Federal Specifications and Standards), Data Item Descriptions (DIDs), and other DODSSP Products. Most Specifications can obtained directly from http://quicksearch.dla.mil/ A. Availability of Cancelled Documents - The DODSSP offers cancelled documentsthat are required by private industry in fulfillment of contractual obligationsin paper format. Documents can be requested by phoning the Subscription Services Desk. B. Commercial Specifications, Standards, and Descriptions - These specifications, standards and descriptions are not available from Government sources. Theymay be obtained from the publishers of the applicable societies. C. Ordnance Standards (OS), Weapons Specifications (WS), and NAVORD OSTD 600 Pages - These type publications may be obtained by submitting a request to: Commander, Indian Head Division, Naval Surface Warfare Center Code 8410P, 101 Strauss Avenue Indian Head, MD 20640-5035 D. On post-award actions, requests for "Official Use Only" and "NOFORN" (Not Releasable To Foreign Nationals) documents must identify the Government ContractNumber, and must be submitted via the cognizant Defense Contract Management Command (DCMC) for certification of need for the document. On pre-award actions such requests must be submitted to the PCO for certification of need for the document. E. NOFORN Military Specifications and Standards (including Amendments, Change Notices and Supplements, but NOT interim Changes) to be ordered from: Contracting Officer NAVSUP-WSS Code 87321 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788 F. Nuclear Reactor Publications Assigned NAVSEA Documents and Identification Numbers (i.e. NAVSEA Welding Standard, NAVSEA 250-1500-1) are to be ordered enue: Commanding Officer NAVSUP-WSS Code 009 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788 G. Technical Manuals Assigned NAVSEA Identification Numbers (i.e. NAVSEA Welding And Brazing Procedure, NAVSEA S9074-AQ-GIB-010/248) are to be ordered from: Commanding Officer NAVSUP-WSS Code 1 Support Branch 700 Robbins Avenue Philadelphia, Pa. 19111-5094 H. Interim Changes and Classified Specifications must be obtained by submitting a request on DD Form 1425 to NAVSUP-WSS. 6.3 Notice To Distributors/Offerors - Consideration for award of contract shall be given only to authorized distributors of the original manufacturer's item represented in this solicitation. If you desire to be considered as a potential source for award of this contract, proof of being an authorized distributor shall be provided on company letterhead signed by a responsible company official and sent with your offer to the Procurement Contracting Officer. DATE OF FIRST SUBMISSION=ASREQ ;Paragraphs 10.2.2 (B,C,D) and 10.2.3 of DI-NDTI-80492 do not apply. Block 12 submit for DCMC approval upon completion of test. Forward approved copy with DD Form 250 to NAVSUP WSS MECH at time of shipment.; Block 12 - Resubmit no later than ;30; days after disapproval. DATE OF FIRST SUBMISSION=ASREQ ;Paragraphs 10.2.2, 10.2.3, 10.3.1 and 10.4 of DI-MISC-80678 Do Not Apply. Certification shall be for tests specified by General Notes 6 of dwg. 803-6397408. Submit for DCMA approval upon completion of tests. Forward approved copy with DD Form 250 to NAVSUP WSS MECH at time of shipment.; Block 12 - Resubmit no later than ;30; days after disapproval.