The Naval Air Systems Command intends to award a sole-source contract to Pioneering Decisive Solutions (PIDESO) for building, supporting, and upgrading the ALR-67(V)3 ATAC Bench and ATAC-4 systems. The work will be performed for a lab located in Jacksonville, Florida. The justification is that PIDESO is the original developer and sole provider of the required proprietary technology and expertise for sustaining F/A-18 aircraft systems. This notice explicitly states it is not a request for competitive proposals. Inquiries should be directed to the specified Contract Specialist.

The Naval Air Systems Command intends to award a sole-source contract to Pioneering Decisive Solutions (PIDESO) for building, supporting, and upgrading the ALR-67(V)3 ATAC Bench and ATAC-4 systems. The work will support a lab located in Jacksonville, Florida. The justification is that PIDESO is the original developer and sole provider of the required proprietary technology and expertise for F/A-18 aircraft systems. The government has determined that only this source can meet the requirements in a timely and cost-effective manner, and that competition would result in substantial, unrecoverable cost duplication. This notice explicitly states it is not a request for competitive proposals.

INTRODUCTION This Sources Sought notice is being posted to satisfy the requirement of Defense Federal Acquisition Regulation Supplement PGI 206.302-1(d). The Naval Air Systems Command (NAVAIR), PMA-26... INTRODUCTION This Sources Sought notice is being posted to satisfy the requirement of Defense Federal Acquisition Regulation Supplement PGI 206.302-1(d). The Naval Air Systems Command (NAVAIR), PMA-265 EW Division, is conducting market research to identify potential sources with the expertise, capabilities, and experience to provide and build the ALR-67(V)3 Advanced Test and Check (ATAC) ATAC Bench. The effort will include support, upgrades, and system enhancements for the ATAC systems, specifically the Advanced Test and Check-Out (ATAC-4) systems for the ALR-67(V)3 lab located in Jacksonville, Florida. The results of this Sources Sought will be utilized to determine if the required product exists in the marketplace and if any Small Business Set-Aside opportunities exist. All Small Business Set-Aside categories will be considered. A site visit is required to determine a suitable source. NAVAIR intends to award a sole source contract to Pioneering Decisive Solutions (PIDESO), the original developer and sole provider of the proprietary technology and specialized expertise required to ensure continued sustainment, operational effectiveness, and electronic protection capabilities for F/A-18 aircraft. No other source has the unique knowledge or capability to perform this work. Eligibility The Product Service Code (PSC) for this requirement is 6625 (TEST, MEASUREMENT, AND DIAGNOSTIC EQUIPMENT) The NAICS code is 334515 (Instrument Manufacturing for Measuring and Testing Electricity and Electrical Signals). REQUIRED CAPABILITIES The Government requires a test and check capability that supports comprehensive verification and validation of advanced electronic warfare (EW) systems such as the ALR-67(V)3 Radar Warning Receiver and associated components for the ALR-67(V)3 lab. This capability should enable BIT level testing of suspect components within a known-good functional test loop and support OFP reload and sanitization procedures to ensure system integrity. The test system must also provide additional Input/Output (IO) test capability for CSP J2 and J7 connectors and allow for testing of Fiber NIC and external system discretions. Furthermore, the solution should provide full EAD functional Millimeter Wave (MMW) and Microwave (MW) performance verification, including noise source injection and MMW BIT video validation. Control of polarization switching and the ability to perform angle-of-arrival (AOA) performance verification is also required. Additional capability must include LBIA JSECTS sweep failure verification and 4-angle sensitivity testing of the low-band antenna. The system should support the ability to radiate specific antennas and quadrants (Forward (LEF) and Aft (EAD), with software-controlled RF switching and bus response monitoring. The test system must integrate with AVSIM-controlled RF switching and response monitoring and remain compatible with current test rack interfaces such as the ALE-47 and ALR-67(V)3 BIT-Analysis Test (BAT) cabling. The intent of this Sources Sought is to assess the state-of-the-art in test technologies capable of meeting these functional requirements in support of ongoing and future EW system sustainment and upgrade programs. The capabilities may include: BIT level testing of suspect components inserted in a known-good functional test loop. OFP Reload & Sanitization Provide additional IO Test Capability for CSP J2 and J7 connectors. Allow testing of Fiber NIC and external system discrete(s) Provide EAD functional MMW and MW Antenna Performance Verification, Noise Source, and MMW BIT video verification. Provide polarization switch control Provide angle of arrival performance verification LBIA JSECTS Sweep Failure Verification 4-angle sensitivity testing of Low Band Antenna Ability to radiate specific antennas and related quadrants (Forward (LEF) & Aft (EAD)) Software control of RF switching and monitoring of BUS responses AVSIM controlled RF switching & Response monitoring Integrate with current test rack interface such as ALE-47 and current ALR-67(V)3 BIT-Analysis Test (BAT) cabling. Special Requirements: MIL-STD-881F -Work Breakdown Structures for Defense Materiel Items MIL-STD-1678-1D - Ch. 2 Fiber Optic Cabling Systems Requirements and Measurements (Part 1: Design, Installation and Maintenance Requirements) (Part 1 of 6 Parts) MIL-STD-1678-2A - Ch. 1 Fiber Optic Cabling Systems Requirements and Measurements (Part 2: Optical Measurements) (Part 2 of 6 Parts) MIL-STD-1678-3C - Ch. 2 Fiber Optic Cabling Systems Requirements and Measurements Physical, Mechanical, Environmental and Material Measurements (Part 3 of 6 Parts) MIL-STD-1678-4C - Ch. 2 Fiber Optic Cabling Systems Requirements and Measurements (Part 4: Test Sample Configuration and Fabrication Requirements) (Part 4 of 6 Parts) MIL-STD-1678-5B - Ch.2 Fiber Optic Cabling Systems Requirements and Measurements (Part 5: Design Phase, Supplemental and Legacy Measurements) (Part 5 of 6 Parts), MIL-STD-1678-6A - Ch.2 Fiber Optic Cabling Systems Requirements and Measurements (Part 6: Parts and Support Equipment Commonality and Standardization Requirements) (Part 6 of 6 Parts) MIL-STD-3018 - Parts Management, w/Ch 2 MIL-STD-11991B - GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES 02- 026.07 - F/A-18 Hornet (All Series) and Electronic Attack EA-18G Security Classification Guide (SCG) PMA-265 Systems Engineering Plan (SEP) PMA-265 Configuration Management Plan Program Protection Plan (PPP) Rev 1 for the F/A-18 E/F and EA-18G Aircraft/Systems Program DFARS 252.204-7000 - Defense Federal Acquisition Regulation Supplement (DFARS) DoD S-5230.28 - Policy for Low Observable (LO) and Counter Low Observable (CLO) Programs DoDD 5205.02E - DOD Operations Security (OPSEC) Program DoDM 5205.02 - DOD Operations Security (OPSEC) Program Manual 3 DoDI 5200.39 - Critical Program Information (CPI) Identification and Protection within Research, Development, Test, and Evaluation (RDT&E) DoDI 5200.48 - Controlled Unclassified Information (CUI)