Inactive

Please request the Request for Information HMIT PDF and/or Word Document from the listed Primary POC. REQUEST FOR INFORMATION Helmet Mounted Integrated Targeting (HMIT) Sub-assembly Repair & Depot Sup... Please request the Request for Information HMIT PDF and/or Word Document from the listed Primary POC. REQUEST FOR INFORMATION Helmet Mounted Integrated Targeting (HMIT) Sub-assembly Repair & Depot Support Services The Government is conducting market research to identify potential sources that possess the repair data, expertise, capabilities, and experience to meet qualification requirements to repair the Helmet Mounted Integrated Targeting (HMIT) sub-assemblies. The National Stock Numbers (NSN) and Part Numbers (PN) are as follows: Description Backlight Front Panel Baseboard SBC Wildcat Filterboard Upgrade -22210 to -22350 Wire harness BACKLIGHT FRONT PANEL PCBA BASE BOARD Filter PCBA Wire harness Battery Holder PCBA J-BOX ASSEMBLY MOHAWK SHROUD J-BOX ASSEMBLY EXTENDED MOHAWK SHROUD NHA WC 1 & 2 WC 1 & 2 WC 1 & 2 WC 1 & 2 WC 1 & 2 WC 1 & 2 ICU 800 ICU 800 ICU 800 ICU 800 ICU 800 Mohawk BBA Mowhawk BBA Mowhawk BBA Ext Mowhawk BBA Ext P/N A13278-1 V14739-08-01 A13882-3 A13965-2 A13748- 22350-R A13421-1 A13278-1 A13044-1 A13743-1 A13421-1 A13747-1 V14492-17-01 V14484-01-02 V14492-17-02 V14484-01-04 NSN TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD 5935-01-670- 5622 TBD TBD TBD The entire HMIT system is currently repaired by Thales Visionix, Inc under the Interim Contract Support (ICS) FA8202-17-D-0002. This service has been performed multiple times by Thales, who is the original manufacturer of the HMIT system. This will be a first time repair of the circuit cards separately from the Next Higher Assembly (NHA) Interface Control Unit (ICU). The technical data required to organically repair or compete the repair is not owned by the Government, and is uneconomical to acquire the data by purchase or to reverse engineer the item. No samples are available for potential suppliers to evaluate. Contractor shall furnish all material, support equipment, tools, test equipment, and services. The contractor is responsible for providing, maintaining, and calibrating all support equipment required at their facility or a subcontractor’s facility. Contractor furnished material or parts used ll equal or exceed the quality of the original material or parts. Thales is the manufacturer of the HMIT system and the known sole source contractor for repair of this item. Contractors/Institutions responding to this market research are placed on notice that participation in this survey may not ensure participation in future solicitations or contract awards. The government will not reimburse participants for any expenses associated with their participation in this survey. FAR 52.215-3, Request for Information or Solicitation for Planning Purposes (Oct 1997) applies to this request for proposal: (a) The Government does not intend to award a contract on the basis of this request or to otherwise pay for the information solicited except as provided in subsection 31.205-18 Bid and Proposal (B&P) Costs, of Federal Acquisition Regulation (b) Although "proposal" and "offeror" are used in this Request for Information, your response will be treated as information only. It shall not be used as a proposal. (c) This solicitation is issued for the purpose of: informational planning and budgetary forecasting by the government. INSTRUCTIONS: 1. The document(s) below contain a description of the HMIT repair requirements and a Contractor Capability Survey. The Survey allows Contractors to provide their company’s capability. 2. If, after reviewing these documents, you desire to participate in the market research, you should provide documentation that supports your company’s capability in meeting these requirements. Failure to provide documentation may result in the government being unable to adequately assess your capabilities. If you lack sufficient experience in a particular area, please provide details explaining how you would overcome the lack of experience/capabilities in order to perform that portion of the requirement (i.e., teaming, subcontracting, etc.) a. Identify any areas of work that your organization believes should be broken out exclusively for Small Business. 3. Both large and small businesses are encouraged to participate in this Market Research. Joint ventures or teaming arrangements are encouraged. 4. Questions relative to this market survey should be addressed to Lorie Burton, Program Manager, 478-955-3360 or via email at lorie.burton@us.af.mil. Helmet Mounted Integrated Targeting (HMIT) Sub-assembly Repair & Depot Support Services PURPOSE/DESCRIPTION The Government is conducting market research to identify potential sources that possess the expertise, capabilities, and experience to meet qualification requirements to provide depot-level test and repair of the Helmet Mounted Integrated Targeting (HMIT) sub-assemblies and Depot support services for the Next Higher Assemblies (NHA). The National Stock Numbers (NSN) and Part Numbers (PN) are as follows: Description Backlight Front Panel Baseboard SBC Wildcat Filterboard Upgrade -22210 to -22350 Wire harness BACKLIGHT FRONT PANEL PCBA BASE BOARD Filter PCBA Wire harness Battery Holder PCBA J-BOX ASSEMBLY MOHAWK SHROUD J-BOX ASSEMBLY EXTENDED MOHAWK SHROUD NHA WC 1 & 2 WC 1 & 2 WC 1 & 2 WC 1 & 2 WC 1 & 2 WC 1 & 2 ICU 800 ICU 800 ICU 800 ICU 800 ICU 800 Mohawk BBA Mowhawk BBA Mowhawk BBA Ext Mowhawk BBA Ext P/N A13278-1 V14739-08-01 A13882-3 A13965-2 A13748- 22350-R A13421-1 A13278-1 A13044-1 A13743-1 A13421-1 A13747-1 V14492-17-01 V14484-01-02 V14492-17-02 V14484-01-04 NSN TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD 5935-01-670- 5622 TBD TBD TBD The HMIT system is comprised of an Interface Control Unit (ICU) installed on the F-16 and A-10 aircraft and a Banana Bar located on the helmet. The ICU and Banna Bar are Line Replaceable Unit (LRU) and the sub-assemblies are Shop Replaceable Units (SRU). Each aircraft has one ICU installed. HMIT provides aircrew the ability to cue sensors and weapons, while receiving target, weapon and flight data, at high off-boresight angles for navigation and air-to-air/air-to- ground weapon delivery while maintaining visual contact with the target. The system also provides aircrew the ability to cue weapons to potential targets and other locations via information provided by aircraft sensors. The service shall include providing obsolete parts resolution along with the necessary engineering to investigate Deficiency Reports and to provide engineering support to the Depot as required. The Government does not own the data or the rights to the data needed to compete the repair of this part. It has been determined to be uneconomical to reverse engineer the data, qualify a new source, or buy the data and/or data rights. Thales Visionix, Inc. is the only source of known repair for this system and has been since it was fielded. CONTRACTOR CAPABILITY SURVEY Helmet Mounted Integrated Targeting (HMIT) Sub-assembly Repair & Depot Support Services Part I. Business Information Please provide the following business information for your company/institution and for any teaming or joint venture partners: • Company/Institute Name: • Address: • Point of Contact: • CAGE Code: • Phone Number: • E-mail Address: • Web Page URL: • Size of business pursuant to North American Industry Classification System (NAICS) Code: NAICS Code 811219 – Other Electronic and Precision Equipment Repair and Maintenance Based on the above NAICS Code, state whether your company is: • Small Business (Yes / No) • Woman Owned Small Business (Yes / No) • Small Disadvantaged Business (Yes / No) • 8(a) Certified (Yes / No) • HUBZone Certified (Yes / No) • Veteran Owned Small Business (Yes / No) • Service Disabled Veteran Small Business (Yes / No) • Central Contractor Registration (CCR). (Yes / No) • A statement as to whether your company is domestically or foreign owned (if foreign, please indicate the country of ownership). Written responses or e-mails must be received no later than close of business 15 January 2023. Please email or mail your response to: Lorie Burton Program Manager Common Avionics 407 SCMS/GULBA 235 Byron St, Suite 19A Robins AFB, GA 31098-1670 Questions relative to this market research should be addressed to Lorie Burton, Program Manager, 478-955-3360 or via email at lorie.burton@us.af.mil. Part II. Capability Survey Questions A. General Capability Questions: 1. Describe briefly the capabilities of your facility and nature of the goods and/or services you provide. Include a description of your staff composition and management structure. 2. Describe your company's past experience on previous projects similar in complexity to this requirement. Include contract numbers, a brief description of the work performed, period of performance, and agency/organization supported. 3. Describe your company’s experience in repairing the HMIT and/or sub-assemblies. 4. Describe your company's capabilities for generating, handling, processing and storing classified material and data. 5. What is your company’s current maximum capacity per month for this particular type of requirement? Provide information on any facility reserves you may possess to increase capacity in the event of an immediate need do to critical operational mission requirements. B. Repair Questions: 1. Describe your capabilities and experience in repairing existing systems/equipment (hardware and software) to solve maintenance and support problems in the depot environment. 2. Describe your configuration management processes and how you identify and resolve parts obsolescence and diminishing manufacturing sources problems? 3. Discuss your process for addressing any fit, form, and or function issues that may arise out of this effort. 4. Describe your process for maintaining inventory records and reporting on hand/work-in- process balances and repair status to your customer. 5. How will your organization address the absence of drawings, specifications, technical data, test procedures, etc. 6. If the item cannot be repaired in total, state what your organization can repair. C. Commerciality Questions: 1. Are there established catalog or market prices for our requirement? 2. If you offer this product and/or service to both U.S. Government and commercial sources, is the same workforce used for both the U.S. Government and general public? 3. Describe your standard warranty and return process for goods and services furnished to the government for items similar in nature to this requirement. D. Continuity of Operations and Cybersecurity 1. Does your company have an active Continuity of Operations Plan (COOP) or equivalent in the event of a natural disaster or other catastrophic event that causes facilities or operations to be disrupted? 2. What mitigation strategies are in place for your company to resume operations and to prevent further disruptions? 3. Is your company facing financial disruption, impending merger, acquisition and/or foreign investment? 4. If there is Foreign Ownership, Control or Influence (FOCI) of your company, what percentage of the company is owned by the foreign entity(ies)? Which foreign country(ies)/entity(ies) owns part or all of your company? 5. Does your company have a policy/plan for preventing and mitigating risks associated with internal and external information systems security? 6. Has your company implemented cybersecurity requirements given in DFARS clause 252.204-7012, "Safeguarding Covered Defense Information and Cyber Incident Reporting"?