Inactive Total Small Business Set-Aside (FAR 19.5)

------------------------------------------------Update----------------------------------------------------------- PWS has been updated to Version 8. Under 1.3 Specific Requirement statement 1.3.1 was ... ------------------------------------------------Update----------------------------------------------------------- PWS has been updated to Version 8. Under 1.3 Specific Requirement statement 1.3.1 was added. All other statements remain the same. 1.3.1 Contractor shall only install equipment IAW the Physical Access Control System (PACS) products listed under the “Approved” section which have met the security and functional requirements set by GSA’s FIPS 201 Evaluation Program, and have been approved for use by the Federal Government. Products may be viewed at: FIPS 201 Approved Product List (idmanagement.gov) ----------------------------------------------------------------------------------------------------------------- Funds are not currently available for this requirement. An award shall not be made until funds are certified and made available. This requirement is for removal, install, maintenance and repair of an automated entry control security system (AECS) vindicator-based badge entry combined with a pin-based reader that allows authorized personnel identified by management to enter the Andrews Regional Command Post (ARCP) at 1220 Operations Drive. The AECS system will need to be operational 24 hours per day, 7 days per week. The solution must employ state-of-the-art door entry reader technology capable of reading DoD Common Access Cards (with associated pin), and commercially available 125 kHz cards, as well as remote entry unlock capability, and four internally managed access configurations. The solution requires prompt service response and support in the event of system failures or malfunctions. The new system must be installed and maintained in accordance with the Performance Work Statement (See Attachment 1) and at locations marked in the Design (See Attachment 2). For offers to be considered a Site Visit must be attended. The Site Visit shall take place on May 16, 2024, at 11:00am. Use Attachment 4 - Visitor Request Form to submit information to corey.wallace@us.af.mil no later than May 13, 2024. Any question must be submitted to POC's by May 20, 2024, at 12:00pm EST. All responses will be posted on SAM.gov. Please see the attached Combo Synopsis and Solicitation and follow the Instructions to Offerors to provide an offer. Email offers to the primary and secondary points of contact by the response deadline of May 22, 2024, no later than 12:00pm EST.

Inactive Total Small Business Set-Aside (FAR 19.5)

SOURCES SOUGHT: THIS IS NOT A NOTICE OF REQUEST FOR QUOTATION. THIS IS FOR INFORMATION AND PLANNING PURPOSES ONLY! This notice does not constitute a commitment by the Government. All information submi... SOURCES SOUGHT: THIS IS NOT A NOTICE OF REQUEST FOR QUOTATION. THIS IS FOR INFORMATION AND PLANNING PURPOSES ONLY! This notice does not constitute a commitment by the Government. All information submitted in response to this announcement is voluntary and the Government will not pay for information requested nor will it compensate any respondent for any cost incurred in developing information provided to the Government. Andrews Air Force Base anticipates a requirement that is being considered under a small business set-aside program. The North American Industry Classification Systems (NAICS) Code proposed is 561621. The size standard is $25.0 million. The purpose of this procurement is to aquire services to install, maintenance and repair of a electronic security system vindicator-based badge entry combined with a pin-based reader that allows authorized personnel identified by management to enter the Andrews Regional Command Post. The install shall use equipment that works with the Restricted Area Badge (RAB) issued that is a HID product part number 1386LGGMN with a format of H10301 with a facility code of 89. All readers will also support DoD Common Access Cards and commercially available 125 kHz proximity cards. 1. Eight existing card readers with PIN capabilities will be replaced 2. Three motion sensors will be removed and replaced with three access readers. 3. Two card readers will be installed at exit entrapment areas. 4. One card reader with PIN capabilities and one exit motion sensor will be installed for entry and exit of the Crisis Action Team. 5. Install new emergency release and reconfigure an existing emergency release for entrapment doors. 6. Tag new and exisiting wires in the existing panels and remove existing panels, patching damage to wall by the removal of panels and card readers. 7. Provide one four hour session of systems training for up to four users. Specifics are subject to change as this is a Sources Sought for informational and planning purposes only. Reponses to this Sources Sought request should reference "Automated Entry Control System" and shall include the following information in this format: 1. Company name, address, point of contact name, phone number, fax number and email address. 2. Unique Entity ID, Contractor and Government Entity (CAGE) Code. GSA contract number, if applicable. 3. Size of business – Large Business, Small Business, Small Disadvantaged, 8(a), Hub-zone, Woman-owned and/or Service-Disabled Veteran-owned. A copy of SAM.GOV active registration. Must reflect Commercial and Government Entity, and Reps/Certs. 4. Capability statement displaying the contractor’s ability to provide the products or services, to include past performance information. If past performance information is provided, please include only relevant past performance on the same/similar work within the last 5 years. Please also include in past performance information the contract numbers, dollar value, and period of performance for each contract referenced in the response to this Sources Sought. Note: The Government is still determining the acquisition strategy. If this acquisition will be a small business set-aside, then FAR clause 52.219-14, Limitations on Subcontracting, applies. A key factor in determining if an acquisition will be a small business set-aside is that two or more potential small business prime contractors must be capable of performing at least 50% of the effort, as defined in FAR clause 52.219-14. If it is determined that a small business set-aside is appropriate and your company anticipates submitting a proposal as the prime contractor for a small business set-aside, please provide specific details and rationale as to how compliance with FAR clause 52.219-14 would be achieved, including specific details regarding teaming arrangements, and if subcontracts are to be used, provide anticipated percentage of the effort to be subcontracted and whether small or large business subcontractors will be used. Teaming and/or subcontracting arrangements should be clearly delineated and previous experience in teaming must be provided. NOTE: All contractors doing business with the Federal Government must be registered in the System for Award Management (SAM) database. The website for registration is www.sam.gov. All responses to this notice are to be submitted by 08:30 AM Eastern Standard Time, on 22 April 2024. Responses will be accepted via electronic means only to jessee.vasquez_arguera@us.af.mil or antoine.toran.1@us.af.mil.