Inactive Total Small Business Set-Aside (FAR 19.5)

THIS IS ONLY A REQUEST FOR INFORMATION FOR MARKET RESEARCH PURPOSES. NO FORMAL REQUIREMENT IS DEFINED OR ESTABLISHED. NO ADDITIONAL INFORMATION IS AVAILABLE.? The Standardized Security Forces Ballisti... THIS IS ONLY A REQUEST FOR INFORMATION FOR MARKET RESEARCH PURPOSES. NO FORMAL REQUIREMENT IS DEFINED OR ESTABLISHED. NO ADDITIONAL INFORMATION IS AVAILABLE.? The Standardized Security Forces Ballistic Helmet shall: 1. Meet or Exceed National Institute of Justice (NIJ) Level-IIIA with ballistic performance per(IAW) NIJ STD 0106.01/NIJ STD 0108.01. 2. Meet or exceed current Advanced Combat Helmet (ACH) Blunt Impact Protection requirements IAW AR/PD 10-02 while providing a center channel for communication headband clearance. 3. Padding/Liner System: The helmet must provide a dual-layered adjustable individual padding system (with at least 14 individual pads) to accommodate the respective sizing spectrums identified below. The padding systems must have comfort foam sealed with anti- microbial wicking fabric. The padding system must have a removable center pad to accommodate overhead communications systems easily. Replacement pads and systems need to be available for replacement purchases. 4. Color: The helmet must be available in Coyote Brown and Black in color with helmet covers available in Tactical Black and Operational Camouflage Pattern (OCP) (Note: The helmet cover must fit on the helmet reflecting a tactical appearance, i.e., assist with concealment for operations in a tactical environment). Replacement covers need to be available for replacement purchases. 5. Helmet Cover: Each helmet must come with a helmet cover. Covers must be available in Tactical Black and Operational Camouflage Pattern (OCP) (Note: The helmet cover must fit on the helmet reflecting a tactical appearance, i.e., assist with concealment for operations in a tactical environment). Replacement covers need to be available for replacement purchases. The helmet cover must have Velcro in the exact locations as the helmet's shell with the addition of a bungee retention system integrated into the Velcro patch on the top/center of the helmet cover. The helmet cover must have a cable management system integrated into it. The helmet cover must have an opening in the front to accommodate the NVG shroud. Helmet covers must come with an optional OCP in color counterweight pouch with Velcro closure and ability to attach to side rails via strap or elastic band (tan). 6. Retention System: The retention system must meet ACH pull strength requirements with ahigh-strength hook and loop attachment. Feature a dial retention system and a single one- handed action quick-release capability utilizing high-strength materials resistant to weather and perspiration degradation. The chinstrap must have locking mechanisms to secure straps and prevent slippage. Chinstrap must include additional padding sewn into the dual straps for the chin. 7. Chinstrap Extender: Each helmet must come with a chin strap extender to allow the wearer to wear a Military Chemical Suit Jacket top and the M50 Joint Service General Purpose Gas Mask. When worn, the chin strap must be able to be fastened with both accouterments. 8. Night Vision Shroud: Each helmet must include a coyote brown or black detachable WILCOX three-hole night vision shroud (Part # 56100G34, Cage: 004S1)compatible with the night vision devices listed in Para. 8(i). i. The helmet shroud must accommodate the following accessories: 1)AN/PVS-7B: 5855-01-228-0937 2)AN/PVS-7D: 5855-01-422-5413 3)AN/PVS-14: 5855-01-423-0524 4)AN/PVS-31A: 5855-01-618-8462 5)AN/PSQ-20: 5855-01-534-6449 6)NVG Bracket Mount: 5340-01-509-1467 9. Left and Right Accessory Rail Connector System (Side): Each helmet must include a coyote brown or black side accessory rails connector system must attach via bolts and be attached on the left and right sides of the helmet. The rails system must consist of (1) Magpul MOE 5-Slot Mounting Kit with Two (2) 5-Slot Picatinny Rails for mounting standard Picatinny/MIL-STD-1913 accessories. a. Due to the past performance of Security Forces units, feedback has indicated the critical need that all that mounts and rails must be mounted via bolts to provide the necessary security to minimize potential defects. b. The end-users need to replace shrouds and rails has been proven relevant. c. The accessory rail connector system must have slots for custom mounting and compatibility to accommodate tactical headsets and must be able to adjust the below accessories (see items below #i). i. The helmet rails must accommodate the following accessories: 1)Surefire: HLM-01-TN 2)Princeton Tech Switch MPLS LED Task Light 3)Liberator IV and V Advanced Dual Communication Headsets 4)3M Com-TAC VINIB Peltor Headsets 5)M-50 Gas Mask: 4240-01-512-4437 6) Paulson Riot Shield AGL PPK1007R 10. Ear Clearance: Provide more clearance around the ear than the ACH mid-cut, cover the entire head area, and have a high-cut ear area. Must have a military-grade Velcro patch on the helmet's shell on the right and left side above the rail (2" x 3 ½"). Military-grade Velcro patch on the top/center of the helmet shell (2" x 6 ½"). 11. Jump Certification: The helmet must be listed on the United States Air Force (USAF) Approved for Use List (AUL) as required by Air Force Instruction (AFI) 10-3503, Personnel Parachute Program, paras. 4.3.1 and 4.4.1. 12. Military-grade Velcro patches: The helmet must have a Military-grade Velcro patch on the rear/base of the helmet (1 ½" x 6") with (3 ½") in height along the rear of the rails only. 13. Helmet Weight: The helmet weight must be between 1.6 lbs. and 2.8 lbs. before and after shroud installation, accessory rail, impact liner, and retention system. 14. Fit Sizes: Helmets must accommodate hat sizes from 6 5/8 -7 ½ and 7 3/8 -7 7/8 or head circumferences (inches) 20.5-23.5 and 23-24.75. Fit head sizes 52-63cm with shell sizes. 15. Care Instructions: Each helmet must come with individual care/handing instructions, how to fit, and a wear guide included with the helmet. 16. Be fully Berry Amendment compliant. 17. Must accommodate ballistic mandible. THIS IS ONLY A REQUEST FOR INFORMATION FOR MARKET RESEARCH PURPOSES. NO FORMAL REQUIREMENT IS DEFINED OR ESTABLISHED. NO ADDITIONAL INFORMATION IS AVAILABLE.