Inactive

DLA-Aviation is issuing this sources sought synopsis as a means of conducting market research to identify parties having an interest and the resources to support this requirement to remove old equipme... DLA-Aviation is issuing this sources sought synopsis as a means of conducting market research to identify parties having an interest and the resources to support this requirement to remove old equipment, design, fabricate, and install tanks and equipment to support the wet chemical cleaning processes for various metal parts. Required chemical cleans are as follows: alkaline deruster, aqueous degreaser, epoxy paint stripper, alkaline permanganate scale conditioner, and mildly acidic scale remover wet processes. The fully developed system with all sensors and instrumentation must integrate into the Navy’s existing Direct Digital Control (DDC) system and provide updated graphics for the front-end operating system, Desigo, for the remote monitor and control of the system. Chemical Cleaning Line processing must include Push-Pull ventilation system, consisting as follows: Pull Side Ventilation Hoods, Exhaust Stack, Exhaust Fans, and Mist Eliminators. Exhaust Stack must be designed to handle the CFM requirements and achieve an exit air velocity between 3000-4000 feet per minute (FPM). Stack shall not have any cap or obstruction that would interfere with the exhaust air from traveling vertically from the stack. Stack shall reach a minimum height of 65 feet from grade and fabricated from 3/16’’ and ¼” thick PVC. Push Pull Ventilation must comply with must comply with the San Diego Air Pollution Control District (SDAPCD) Rule, SDAPCD Rule 67.61, “Cold Solvent Cleaning and Stripping Operations”; American Conference of Governmental Industrial Hygienists (ACGIH) Standard, “Industrial Ventilation: A Manual of Recommended Practice for Design”, (specifically §13.70 Open Surface Tanks and §13.72 Push-pull Ventilation); and the American Society of Safety Professionals (ASSP) Z9.1 Standard, “Ventilation and Control of Airborne Contaminants during Open-surface Tank Operations”. Mist Eliminator ahead of the exhaust fans shall remove 98% of droplets 20 microns or greater. Potential sources must provide turn-key machine with technical data, delivery, shipping, unloading and rigging, installation, removal of old equipment, equipment labeling/markings in compliance with MIL-STD-130N, testing and on-site operator, maintenance, electrical, and mechanical training. The result of this market research will contribute to determining the method of procurement. The proposed contract action is for supplies or services for which the Government intends to solicit and negotiate with only one source under authority of FAR 6.302. Interested persons may identify their interest and capability to respond to the requirement or submit proposals. THIS SOURCES SOUGHT IS FOR INFORMATION PURPOSES ONLY. THIS IS NOT A REQUEST FOR QUOTE/PROPOSAL. IT DOES NOT CONSTITUTE A SOLICITATION AND SHALL NOT BE CONSTRUED AS A COMMITMENT BY THE GOVERNMENT. RESPONSES IN ANY FORM ARE NOT OFFERS AND THE GOVERNMENT IS UNDER NO OBLIGATION TO AWARD A CONTRACT AS A RESULT OF THIS ANNOUNCEMENT. NO FUNDS ARE AVAILABLE TO PAY FOR PREPARATION OF RESPONSES TO THIS ANNOUNCEMENT. ANY INFORMATION SUBMITTED BY RESPONDENTS TO THIS TECHNICAL DESCRIPTION IS STRICTLY VOLUNTARY. A determination by the Government not to compete this proposed contract based upon responses to this notice is solely within the discretion of the government. Information received will normally be considered solely for the purpose of determining whether to conduct a competitive procurement. Submission Instructions: All responses under this Sources Sought Notice must be emailed to AVN IPE Market Research at AVNIPEMarketResearch@dla.mil. Email subject line must include ATTN: IPE TRACKING NUMBER 22-40-1003, C1 Cleaning Line). Responses should not exceed ten (10) one-sided 8.5 x 10 inch pages with a font that is no smaller than 10 point as this is not a request for a proposal but only a request for submission of a vendor's capability to perform this requirement. Telephone inquiries will not be accepted or acknowledged, and no feedback or evaluations will be provided to companies regarding their submissions. DLA Aviation intends to issue a request for proposal for one Cleaning Process Line. Interested parties may identify their interest and capability to respond to this requirement no later than the stated closing date/time. Place of performance is Fleet Readiness Center Southwest, NAS North Island, San Diego DLA Aviation is requesting industry input into the feasibility of the government’s requirements. In your response, please provide: Description of your company’s capabilities, based on the questions below Please identify your company’s business size in terms of number of employees, and whether domestic or foreign for consideration of solicitation set-aside, and small business subcontracting requirements. Please identify your company’s manufacturer status: Manufacturer/Non-Manufacturing Source. If non-manufacturing source, please identify the manufacturer. Please identify whether your company will partner with subcontractors to complete this requirement. Please provide a basis of estimate to consider the total financial budget of this requirement. Estimates should capture the total procurement requirements, not solely the machine’s requirements.