Inactive Total Small Business Set-Aside (FAR 19.5)

COMBINED SYNOPSIS/SOLICITATION Purchase of Formlabs 3L 3D Printer and Accessories (I) This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpar... COMBINED SYNOPSIS/SOLICITATION Purchase of Formlabs 3L 3D Printer and Accessories (I) This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice and in accordance with the simplified acquisition procedures authorized in FAR Part 13. This announcement constitutes the only synopsis/solicitation; proposals are being requested and a written solicitation will not be issued. (II) This solicitation is issued as a request for quotation (RFQ). Submit written quotes on RFQ Number PMEL-20-00997. (III) The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2020-06. (IV) This solicitation is being issued with a total small business Set-aside. The associated NAICS code is 333244, PSC code 7025. (V) This combined solicitation/synopsis is for purchase of the following commercial items: PMEL is a research and development laboratory that conducts both scientific and engineering R&D. A key purpose of the laboratory is to enhance NOAA’s observational capability through the development of technology, including sensors, vehicles and observational arrays. To fulfill this mission, PMEL engineers are constantly building and testing prototype instruments. 3-D printing technology uses additive manufacturing to produce parts by precisely adding material to build the part from the ground up, as opposed to traditional subtractive machining techniques where a block of material is machined away to produce the part. This can result in considerably less waste when creating parts with complex geometry, like meshes. The distinct advantages of 3-D print manufacturing are the ability to rapidly produce accurate parts at the press of a button, design and produce parts that would be impossible to manufacture using traditional machining processes, and create parts with very complex geometry including complex curving surfaces and small interior channels. This purchase will enhance PMEL’s additive manufacturing capability by adding the ability to print large functional air and water tight parts. This will allow NOAA PMEL to print protype and 1-off housings, endcaps and molds quickly and efficiently, saving PMEL money. (VI) Description of requirements is as follows: Quantity of 1 each of the following items. Formlabs 3L Printer Form 3L Finish Kit Form 3L Build Platform Form 3L Resin Tank (VII) Date(s) and place(s) of delivery and acceptance 8/30/2020 FOB Origin within CONUS by Government Bill of Lading (GBL), NOAA/PMEL Seattle, WA 98115-6349 (VIII) Questions must be emailed to the attention of Ben Carlson. The email address is Ben.Carlson@noaa.gov , 206-526-4321. THE FOLLOWING PROVISIONS AND ATTACHED CLAUSES APPLY TO THIS ACQUISITION FAR 52.204-7 System for Award Management FAR 52.212-1, Instructions to Offerors -- Commercial Items applies to this acquisition. FAR 52.212-3, Offeror Representations and Certifications – Commercial Items FAR 52.203-18 Prohibition of Contracting with Entities that Require Certain Internal Confidentiality Agreements or Statements—Representation FAR 52.225-2 -- Buy American Certificate. As prescribed in 25.1101(a)(2), insert the following provision: Buy American Certificate (May 2014) (a) The offeror certifies that each end product, except those listed in paragraph (b) of this provision, is a domestic end product and that for other than COTS items, the offeror has considered components of unknown origin to have been mined, produced, or manufactured outside the United States. The offeror shall list as foreign end products those end products manufactured in the United States that do not qualify as domestic end products, i.e., an end product that is not a COTS item and does not meet the component test in paragraph (2) of the definition of “domestic end product.” The terms “commercially available off-the-shelf (COTS) item,” “component,” “domestic end product,” “end product,” “foreign end product,” and “United States” are defined in the clause of this solicitation entitled “Buy American—Supplies.” (b) Foreign End Products: Line Item No.: Country of Origin: CAR 1330-52.222-70 Sexual Assault and Sexual Harassment Prevention and Response Policy CAR 1352.201-70 Contracting Officer’s Authority CAR 1352.209-73 Compliance with the Laws CAR 1352.209-74 Organizational Conflict of Interest CAR 1352.215-72 Inquiries CAR 1352.233-70 Agency Protests CAR 1352.233-71 GAO and Court of Federal Claims Protests CAR 1352.237-71 Security Processing Requirements - Low Risk Contracts CAR 1352.246-70 Place of Acceptance